| Ottawa, Ontario | MER5875QCF | No code. | Oven will not heat up past 280. Element and sensor replaced and problem still exists. | Repaired |
| Shelburne, Ontario | MER5875QCF | F1 | Oven not heating up. Already replaced heating element | Repaired |
| London, Ontario | MER5875QCF | N/A | Display was dead after power outage. Reset circuit breaker. Stove is receiving power as stove elements work. | Repaired |
| Victoria, British Columbia | MER5875QCF | no code | After power outage, control panel dead. No display and buttons unresponsive. Stove elements work fine. | Timer inspected, no repairs necessary |
| Winnipeg, Manitoba | | none | temp no longer staying in sync put new probe in, still the same problem too hot | Awaiting receipt of timer |
| Winnipeg, Manitoba | MER5875RCF | 03.0 | When power is turned on, "03.0" appears in display. Press Cancel and the time starting at 12:00 shows. There is a double beep every minute. No other touch buttons work. If you hold down Cancel then hold down any other button, you get a double beep after 3 seconds. | Awaiting receipt of timer |
| Winnipeg, Manitoba | MER5875RCF | 03.0 | When power is turned on, "03.0" appears in display. Press Cancel and the time starting at 12:00 shows. There is a double beep every minute. No other touch buttons work. If you hold down Cancel then hold down any other button, you get a double beep after 3 seconds. | Awaiting receipt of timer |
| SPRINGSTEIN, Manitoba | MER5875QCF | N/A | Oven over heats , Temp keeps climbing even once it has beeped ( up to temp) Seems to level out at 50 to 80 F higher depending on where you set the calibration adjustment to. | Awaiting receipt of timer |
| Gatineau, Québec | mer5875qcf | N/A | d ont work | Awaiting receipt of timer |
| RAWDON, Québec | MER5875QCF | NONE | FAIL DURING THE DAY, WHEN COMING BACK FROM WORK IT WAS BLACK.<br />
NO POWER FAILURE OR EVIDENCE OF SURGE DURING THIS DAY.<br />
NO LIGHT IN OVEN. COOK TOP WORKING O.K. | Awaiting receipt of timer |
| St-Constant, Québec | mer575qcf | N/A | any push button works, only set button and cancel button oven works at 350 if I press set button oven can only be stop with the cancel button timer is not avail clock not avail oven light.... | Replaced with reconditioned timer |
| Marieville, Québec | Mer5875qcf | Na | Bake was blinking. Indicating temp satisfied after 15 seconds even when not real. | Awaiting receipt of timer |
| BIBLE HILL, Nova Scotia | | N/A | Shuts down an beeps at random | Replaced with reconditioned timer |
| Brockville, Ontario | MER5875QCF | bake light flashing | In any baking modes, you select a temp. then a few seconds later the display should go from your set temp. to actaul temp., and at the same time the fan symbol and fan motor starts, on this unit the set temp does not go away and then the unit alarms about 15 sec. into the program and the display goes blank except for the bake light flashing, can be cancelled and the display goes back to showing time. The temp. sensor was checked and is OK | Replaced with reconditioned timer |
| BIBLE HILL, Nova Scotia | MER5875QCF | N/A | oven not heating | Replaced with reconditioned timer |
| BIBLE HILL, Nova Scotia | mer5875qcf | N/A | Bake temp not tracking correct. Convect works ok. | Replaced with reconditioned timer |
| Nepean, Ontario | MER5875QCF | 1c8c F14 | When using Convection (Bake) mode, food at the back of the oven, nearest the convection fan, is overcooked. The rest of the food in the oven is cooked properly. Temperature test of oven, using digital temperature probe, indicates that oven temperature is being regulated, and this is also supported by the sound of the control relays clicking during the cooking period. Convection fan is running.<br />
<br />
Diagnostic code is “1c8c” (control board-related). Have also occasionally seen “F14” on the display (this appears briefly when first powering up) but there is no such code listed in the service manual. On-board diagnostics fault code detection does not cancel active cook function. | Timer inspected, no repairs necessary |
| Brockville, Ontario | MER5875QCF | bake flashing after | After setting the desired temp. for baking, the set temp. usually is switched for the actual oven temp but in this case the set temp remains displayed and the fan symbol starts, afetr about 15 seconds the unit alarms and the display goes blank except for the bake light that is flashing rapidly, the temp. sensor is good. | Awaiting receipt of timer |
