CAMCO187D1914P001 General Electric Range/Stove/Oven Timer Repair

Failure codes, problems, and resolutions for General Electric timer model # CAMCO187D1914P001

General Electric (GE) ERCs and General Electric (GE) stove clocks and timers Manufacturer :  General Electric
Part Number :  CAMCO187D1914P001
Appliance Type :  Range/Stove/Oven
Color : 
Description :  Electronic Range/Oven Timer

 
 
Do you have a failed General Electric CAMCO187D1914P001 timer?
Click here:

We can repair or replace your faulty CAMCO187D1914P001 timer.
Request Appliance Timer Service

Recent Service Requests for General Electric Part Number CAMCO187D1914P001

CityModel NumberFailure CodeProblem DescriptionResolution
Blenheim, OntarioGRSR3920ZBB-3F-1When oven is on timer comes up with an F-1 fault code and oven continues to heat upRepaired
Blenheim, OntarioGRSR3920ZBB-3warranty repairWe had the F-1 code repaired and when the timer was returned the clock and the start time button are non functioning. They had worked previously, the buttons seem to have no stability.Beyond Repair
Waldheim, Saskatchewan12591-1none - place to readNo heat to oven element (no voltage off timer side when oven on). Broiler element works. Temperature sensoor fine, reads 1080 ohms. Bake element fine. Likely the oven relay shot. Other number on timer 199-01170-00Repaired
Sooke, British ColumbiaGRSR3920ZSS-1No CodeTurns oven off periodicallyAwaiting receipt of timer
Caledonia, Nova ScotiaN/ANeither oven element turns on, says it is preheating but elements can still be touched after 10min. We had intermittent power outages all weekend so I'm guessing we fried the control panel.Awaiting receipt of timer
Ottawa, OntarioGRSR3920ZWW-3N/AUp button is brokenAwaiting receipt of timer
Georgetown, OntarioGRSR3920Zww-2N/AOven heats up normally and maintains temperature for some time, then shuts off randomly. Clock shows 12:38 after every shut-off. I can turn oven back on immediately and it will go back to normal operating temp. Sometimes it will finish the bake/roast cycle; sometimes it will cut out again. Same failures are described in your "Resolution web page".Beyond Repair
Etobicoke, OntarioGRSR3940ZWW-2n/aOven starts to heat up. Oven stops heating before set temperature is reached. (I was also checking temp. with a mechanical in-oven thermometer) Oven never reaches set temperature - just continues to cool off - and element doesn't come on again - relay seems to stay open. ALSO: If you have a replacement faceplate, I would like to purchase that also - the existing one is cracked.Repaired
Windsor, OntarioGRSR3925ZSS-1F3Was an interrmittant problem but seems to have escalated to where I must unplug Range to reset fault, but when I try to turn on broil or bake the F3 fault returns. Phil(519-979-9755)Repaired
Minden, OntarioN/ANo displayBeyond Repair
Mill Bay, British ColumbiaGRSR3920ZCC-1??Oven stopped working, Elements tested and both upper and lower appear fine. Stove top continues to function.Repaired
Mundleville, New BrunswickF1 & F3F1 and F3 error...I checked the temp probe and probe is fine 1050ohms. I need a refurbished replacementAwaiting receipt of timer
Calgary, AlbertaGRSR3925ZSS-1N/A- Surface elements work fine. - Verified 120V to timer at N/L2 terminals and also at N/L1 - Screen on timer is blank. The time is not shown and nothing appears when buttons are pressed. - Buttons do not appear to turn on the oven element. - None of the little lights on the timer panel come on (e.g. Bake, broil, timer, etc.)Repaired
Shakespeare, OntarioGRSR3920ZWW-4F-4F-4 code. Replaced temperature sensor. No change. Please diagnose and repair or replace with reconditioned.Repaired
Ucluelet, British ColumbiaGRSR3955ZWW-1F1 & F3F1 THEN STOVE COMES ON AGAIN F3 STAYS OFF FOR SOMETIMES HOURS THEN BACK TO NORMALRepaired
Richmond Hill, Ontariogrsf3201zww-5N/ALED display not functional, control buttons not functionalAwaiting receipt of timer
West Vancouver, British Columbiagrsr3920zss-1f1F1 code. Oven does not work.Repaired
Bladworth, SaskatchewanGRSR3920ZWW-4F3Oven will not turn on , tried replacing temp sensor , still throughing F3 codeReplaced with reconditioned timer
Almonte, Ontario12791-2N/ALooks like the relay has burnt, but am happy to just get a reconditioned part. other numbers on the Robertshaw PCB are 100-01176-00, 040448592 JG1, 585/930F/ELECReplaced with reconditioned timer
Bolton, OntarioGRSR3925ZSS-1F1The timer beeps and flashes F1 every half hour or so. Powering down and repowering did not clear the alarm.Repaired