|benton, Arkansas||GE||WB27K5055||N/A||oven only works on max temperature. any setting lower than that, it warms up for one to two minutes and shuts off and reads the set temperature, not the actual temperature.||Beyond Repair|
|South Mills, North Carolina||GE||WB27K5055||N/A||Oven does not reach set temperature.||Repaired|
|huntsville, Alabama||Kenmore||911.4012190||wb27k5055||no code||Oven will not warm to selected temp. You can set oven for 350 and it will beep like it is up to temp after only a minute or so. You can sed oven for 350 and even after 45 min oven will only heat up to around 100 degrees. Heat probe seems to have checked out and seems to be working as it should.||Repaired|
|Ashland, Massachusetts||Kenmore||911.4712991||WB27K5055||F1||F1 on occassion. When I turn on Bake unit shuts off, with no error withing 10 seconds.|
If I start broil and switch to back then the unit works till I shut it off. When I shut it off I then get the F1 error code.
|Mechanicsville, Virginia||General Electric||JDC27GOP2BG||WB27K5055||NONE||Put the range in broil and it works fine. Set it to bake and in about 4 seconds it beeps(instead of 'clicking on') and the 'on' light comes on. When checking current at the bake element I get 120v on the orange wire and 0 on the yellow wire. No codes given.||Repaired|
|Brighton, Tennessee||General Electric||JDC27GOP1BG||WB27K5055||F1||If the timer is beyond repair, then I'd like to purchase one from inventory.|
Symptoms: beeping, non-stop. Code F1 showing in display. Tried simple reset, then cut power to unit and finally took it apart and unplugged the ribbon cable to reset, with no luck.
|Awaiting receipt of timer|
|Pelzer, South Carolina||General Electric||JDC27GP||WB27K5055||F1||When the stove is plugged in, it starts beeping and displaying an F1 fault on the screen. We hit the clear button but it keeps beeping. All of the components function, all eyes heat up and the oven also does, but it constantly beeps and displays the fault.||Beyond Repair|
|ROCHESTER, New York||General Electric||JDS27GP3BG||WB27K5055||F-1||F-1 COMES ON AND TONE KEEPS GOING OFF AND WILL NOT RESET.||Beyond Repair|
|Hebron, Maryland||Kenmore||9114012190||WB27K5055||none||Reading sensor input as 160F @ room temp. - sensor resistance checks out @ 1089 ohms.|
It has now stopped operating the elements (both) since our phone conversation Mon, 10/31 AM.
****PLEASE NOTE: Per our conversation, I understand you should be getting one of these returned shortly from another customer who just purchased an in-stock one. I would like to purchase that one, when rebuilt, if mine is beyond repair. Thank you.
|Mena, Arkansas||Kenmore||911.4012990||WB27K5055||F-1||Oven works fine but it Beeps constantly and displays a F-1 message when oven is not in use.||Repaired|
|Harvest, Alabama||General Electric||JDC27GOP1BG||WB27K5055||none||Controller is 20 years old and it takes forever for the oven to heat up. I have to set the temp. 100 degrees higher on the controller than what is needed and then it takes about an hour for the oven to reach the temperature. Clearly a PID problem, but GE doesn't supply these controllers any longer. Trying to get the oven ready for the holidays. THANKS!||Replaced with reconditioned timer|
|Chesapeake, Virginia||Kenmore||911.4012190||WB27K5055||No failure code give||-Doesn't reach desired temperature (ex. must set to 500 to get 350).|
-Panel buttons extremely difficult to push to enable.
-Heat probe sensor already replaced.
-Baking element already replaced.
|Newnan, Georgia||Kenmore||9114012190||WB27K5055||F1||F1||Awaiting receipt of timer|
|HUNTSVILLE, Alabama||LG||JD527GOP1BG||WB27K5055||NC-RANGE TEMP WILL N||WHEN SETTING RANGE TEMP, A LOUD "DUCK" SOUND COMES FROM THE MODULE AND THE TEMP WILL NOT SET OR HOLD. IT WILL SOMETIMES ACK AS IF IT IS HEATING UP AND WILL SHUTOFF.||Repaired|
|SUMMERVILLE, South Carolina||General Electric||JDS27GOP2BG||WB27K5055||N/A||TIMER COMES ON BUT ELEMENTS IN OVEN DO NOT HEAT UP . AFTER A FEWW SECONDS IT TURNS ITSELF OFF.||Repaired|
|Mascotte, Florida||Kenmore||WB27K5055||F1||Waont warm and beeps.||Awaiting receipt of timer|
|Parsons, Tennessee||General Electric||JDC27GoP1BG||WB27K5055||unknown||Shows 195* temp at room temp. Will not reach selected temp||Awaiting receipt of timer|
|Pass Christian, Mississippi||Kenmore||9114012190||WB27K5055||NONE||when I turn it on it only stays on for a few minutes then it turns back off.||Repaired|
|MORGANTOWN, West Virginia||General Electric||JDS27G0P2BG||WB27K5055||NO CODE||BAKE WILL NOT HEAT UP AND ELEMENT IS GOOD.BROIL AND ALL OTHER LIGHTS WORK I THINK. NO POWER TO LOWER ELEMENT||Repaired|
|Naples, Florida||General Electric||JDC27G0P1BG||WB27K5055||none||Oven timer "beeps" in 1-2 minutes indicating that selected bake temperature has been reached when this is not correct. Temperature selector must be set to max in order to achieve about a 400 temp. Broiler element seems to work OK||Awaiting receipt of timer|
|Bristol, Connecticut||General Electric||JDS26G0R2AD||WB27K5055||None shown||Clock works. Bake and Broil functions buss when selecting them. Also the lower oven coil heats up when selecting the Broil Function (the upper coil does not heat up). When selecting the bake function and touching the up arrow the digital window shows 350 degrees on top and 100 degrees on the bottom, the lower coil begins to heat, but the digital lights go out after about 10 or 15 seconds and the coil begins to cool.||Awaiting receipt of timer|
|West Bloomfield, Michigan||General Electric||JDC27GP2BG||wb27k5055||no code given.Wont g||Wont get to temp. at 500 it only gets to 299|
We need at least a referb if you have one please
|Awaiting receipt of timer|
|Burgettstown, Pennsylvania||Kenmore||911.4012990||WB27K5055||N/A||Oven temp. will only go to about 200 degrees||Awaiting receipt of timer|