Almonte, Ontario | Frigidaire | | N/A | F1 code intermitantly, even when face is disconnected | Replaced with reconditioned timer |
Regina, Saskatchewan | Frigidaire | CFEB786JGS2 | n/a | Oven doesn't bake, yet element reads 25 ohms so it's okay.
Also temp reading you can barely see. It was brighter when new, now you can hardly adjust temp especially at certain times of the day. | Repaired |
Niagara falls, Ontario | Frigidaire | cdeb30s8cc2 | none | Broil ok, bake not working no power at E7 ba | Repaired |
Gatineau, Québec | Frigidaire | cfeb786jgb3 | F-3 | I replaced the oven probe, checked the resistance which is ok (1100 ohms at room temperature) but still getting an F-3 error code. | Replaced with reconditioned timer |
Hemmingford, Québec | Frigidaire | CFEB786JGB | F1 | Keypad frozen, cannot stop buzzing sound following power surge. | Replaced with reconditioned timer |
Oakville, Ontario | Frigidaire | CFEB389WEC7 | F-3 | F-3 frequently occurs, getting worse till now F-3 appears within 5 minutes of oven start.
Removed Control unit and cleaned with rubbing alcohol. Worked better for a few days then failed again. Took back off and checked probe - checks OK @ 1K Ohm | Repaired |
montreal, Québec | Frigidaire | CPEB30S8AC1 | no failure code, jus | The display was working but the oven was not reaching its target temperature. i turned the oven off and on again and heard a POP and the display went DEAD. Just a little note about the type of service preferred...i'd like to rebuild my timer or buy a rebuilt from you whichever is CHEAPER. Thanks | Repaired |
Kingston, Ontario | Frigidaire | CGEB27S7AB1 | No Code but display | Center four buttons operating as one can hear relay energize but will not display temp or "beep" as per usual - will not heat.
All other buttons operate correctly. | Awaiting receipt of timer |
Kirkland, Québec | Frigidaire | CPEB30S8AC2 | F3 | No elements would heat up, and then it would notify F3, but then when opened the box, the electronics just stopped working. | Repaired |
mirabel, Québec | Frigidaire | | N/A | only broil works. had someone come over and he says the relay is broken for the oven part ( i think it is the relay) | Repaired |
Toronto, Ontario | Frigidaire | CPEB30S8CC1 | N/A | I spoke with Howard and I will be dropping it in and then picking it up the same day (August 31, 2010). | Repaired |
Laval, Québec | Frigidaire | Frigidaire | N/A | Get 2 codes can't remember which ones, but basically the oven would just shut off when it would get hot and at that point when I would push on the keypad buttons they wouldn\t work and would be hard | Repaired |
Pierrefonds, Québec | Frigidaire | CGEB27S7AS1 | none | doesn't heat completely (only 120 on one side of element)
output of bake relay doesn't go to 120v at e7 ... suspect relay defective | Repaired |
Dollard des Ormeaux, Québec | Frigidaire | | N/A | Does not light up | Replaced with reconditioned timer |
Rocky Mountain House, Alberta | Frigidaire | Gallery | N/A | loose power to unit approx once week | Replaced with reconditioned timer |
Hanmer, Ontario | Frigidaire | CGEB27S7CS1 | F1 | Getting F1 ERROR, Light staying on, oven turns on for 5 seconds then turns off with F1 error. | Repaired |
Calgary, Alberta | Frigidaire | CPEB3058CC2 | none | I had a qualified service technician come to the house and test the oven. He advises that the clock/timer/EOC is not working properly. I would like to have it fixed. | Repaired |
west kelowna, British Columbia | Frigidaire | cgeb27s7cb1 | f1 | oven will not properly heat, baking element will not come one | Repaired |
ste agathe des monts, Québec | Frigidaire | cgeb27s7cs1 | f1 f3 | when ever we use the oven, after a while the failure code F3 and F1appears | Timer inspected, no repairs necessary |
Richmond Hill, Ontario | Frigidaire | | Stopped working no d | Timer stopped working. There is no display at all. There is power to the range but clock does not function. | Repaired |
Val-des-monts, Québec | Frigidaire | CGEB27S7AB1 | none | Oven will not heat on bake cycle. Broil heats very well. As instructed by your technician I switched leads on Broil relay with bake relay and activated broil and the bake element heated. Repeated same by switching bake lead to broil relay and activated bake and the broil element remained cold. | Repaired |
Wawa, Ontario | Frigidaire | cgeb27s7c13 | N/A | Bake doesn't work. | Repaired |
Paquetville, New Brunswick | Frigidaire | electrolux | N/A | the lower and upper element are not working | Repaired |
Mississauga, Ontario | Frigidaire | | N/A | Oven works only on broiler mode but not on the bake mode. | Repaired |
Nanaimo, British Columbia | Frigidaire | CGEB30S8CS1 | F1 | Oven never heats up past 220F. Broil still works though. | Repaired |
gatineau, Québec | Frigidaire | cpeb30s8cc2 | none | Broil ok, bake not working | Repaired |
Milton | Frigidaire | CPEB30S8AC2 | N/A | | Repaired |
Hanmer, Ontario | Frigidaire | | F1 | Getting F1 Error, oven light is staying on , when turning on oven it stays on for about 5 seconds and then faults to F1 | Awaiting receipt of timer |
Hanmer, Ontario | Frigidaire | | F1 | Getting F1 Error, oven light is staying on , when turning on oven it stays on for about 5 seconds and then faults to F1 | Awaiting receipt of timer |
Richmond Hill, Ontario | Frigidaire | | Stopped working no d | Timer stopped working. There is no display at all. There is power to the range but clock does not function. | Repaired |
Laval, Québec | Frigidaire | CGEB27S7CS1 | N/A | bake does'nt work | Repaired |
west kelowna, British Columbia | Whirlpool | cgeb27s7cb1 | F1 | bake element does not operate, F1 code. Repleaced lower baking element prior, did not fix problem. Oven does not heat to set temp. No moisture problems. | Repaired |
Ottawa, Ontario | Frigidaire | | N/A | | Awaiting receipt of timer |
Bedford, Nova Scotia | Frigidaire | | None | Problem Symptoms:
1. No heat to the Bake Element when the Bake front panel switch selected.
2. No heat when the Convection Bake front panel switch selected (the convection fan does run).
3. There is heat on the Broil Element when the Broil front panel switch is selected.
What I’ve done thus far which has lead me to believe it is the Electronic Control unit:
1. Measured the AC input to the stove from the junction box to ensure the 220VAC mains connection was okay
2. Measured for AC across the connection wires to the bake heating element after pressing the “Bake” front panel switch. No AC present. (Is this a valid test?)
3. Inspected all connections to / from and careful visual inspection of Control Unit (nothing obvious was seen).
4. Tested for continuity across outputs from the "bake" relay; there is NO continuity across the bake relay outputs when the “Bake” switch was selected on the front panel. Relay does not close the contact when energized. | Repaired |
Wawa, Ontario | Frigidaire | | N/A | Bake won't work | Repaired |
Hillier, Ontario | Frigidaire | CFEB789 JGB3 | F1 | continuous beeping . Resetting electricity and quick depression of buttons allows all functions to work, but beeping resumes upon completion of baking broiling etc. F1 displayed. | Repaired |
RR#1 Wilsonville, Ontario | Electrolux | CBEB27S7CB2 | none | clock and controls not working/ burned out | Repaired |
Val d'Amour, New Brunswick | Frigidaire | CFEB786JGS3 | N/A | Oven doesn't heat on Convect bake | Awaiting receipt of timer |
BIBLE HILL, Nova Scotia | Frigidaire | CGEB27S7CB1 | N/A | oven not heating. | Repaired |
Fredericton, New Brunswick | Frigidaire | CGEB27S7CB1 | N/A | Bake element sometimes heats for a short time (2-3 minutes) and then the oven just stays at the same temperature. The broil element does throw some heat during the cycle but just enough to keep the temperature constant. If the oven is on broil, the broil element does glow. I checked the element for continuity and resistance and it is good. I checked for power to the oven and I do get 240V. With the oven partly pulled out, I noticed that the bake element does sometimes start glowing when I tap on the bake relay behind the board. (I wish I could just swap that relay for a new one to check!)
This symptom does seem to be quite common. By the way, I did check the thermal breaker and there is no problem there (except no power reaching it when the bake element is supposed to be on) | Repaired |
Dartmouth, Nova Scotia | Frigidaire | CGEB27S7CB1 | n/a | Door lock motor remains energized and door is locked and cooling fan running all the time. Oven probe resistance measured at 1082 ohms (room temperature / 20C). A few weeks ago the wife noticed a audible "beep" intermittently sounding from the oven accompanied with a Fxx code. Like many other woman, she can't remember what code it was !!!! I'm guessing it had to do with over temperature?
Thanks for your help,
Mike Henri
Zone Manager - Honda Canada Inc.
Halifax, NS | Timer inspected, no repairs necessary |
Balgonie, Saskatchewan | Kenmore | c970-418826 | none | Broil does not work | Awaiting receipt of timer |
St. Catharines, Ontario | Frigidaire | CGEB27S7AB1 | no code displayed | Bottom burner does not heat up.
Top burner is fine.
On broil is fine.
Clock works, tells correct time.
Convection wheel spins. | Repaired |
BIBLE HILL, Nova Scotia | Frigidaire | cfeb386jgb2 | N/A | f3 error code. | Repaired |
Stony Plain, Alberta | Frigidaire | CPEB30S8CC2 | N/A | Broil will not work. I have checked element continuity - good, and wiring continuity between the board and the element - also good. If you have a reconditioned board I would like it. Once I've swapped the board I can send in my old board. Please advise if you have and price.
Thanks, Noel | Awaiting receipt of timer |
Gatineau, Québec | Electrolux | CPEB30S8CC2 | N/A | The bottom element does not come on any more even though I installed a new one | Repaired |
Warkworth, Ontario | Frigidaire | CGEB27S7CB1 | Has none. | Bottom element is not working. Had a service tech look at the oven. Timer / clock has failed. | Repaired |
St. John's, Newfoundland and Labrador | Frigidaire | CGEB27S7CB2 | N/A | Oven not heating on Bake option. The broil option is working. The display lights are working fine aswell. Technician checked oven and stated the circuit board relay is burnt out. | Repaired |
Barrie, Ontario | Frigidaire | CPEB30S8AC2 | N/A | Initially when on bake, temp wouldn't get above 275 degrees. Now there is nothing.
If you can't fix it can I buy this module from you? | Awaiting receipt of timer |
Oro-Medonte, Ontario | Frigidaire | CGEB27S7CB | ? | bake and broil has not worked for some time unless convection selected.
after about 6 months using convection option this also now does not work. oven heats up to about 150 F only. | Repaired |
Carleton Place, Ontario | Frigidaire | CGEB27S7CB1 | n/a | Broiler doesn't work. Have had it diagnosed that the timer/relay is the problem. I would be interested in a reconditioned one if new is not available. | Repaired |
MAPLE RIDGE, British Columbia | Kenmore | C970-418851 | F1 | F1 FAULT COMES RANDOMLY THROUGHOUT DAY AND NIGHT AND CLEARS TEMPORARILY WHEN POWER CYCLED AT BREAKER (CONFIRMED 240VAC+N+GND OK). WHEN NO FAULT, OVEN SEEMS TO WORK FINE (ALL LOADS CHECKED FOR OPERATION). | Repaired |
Gorham, Ontario | Frigidaire | CPEB30S8CC2 | none, bottom element | Bottom element stopped working, no warning signs. Bottom element has been tested and works, just not in my oven. Everything I read and the repairmen I talk to say it is the timer. Hope you can help. | Repaired |
Sarnia, Ontario | Frigidaire | CGEB27S7AB1 | N/A | NOT FUNCTIONING | Awaiting receipt of timer |
Clarenville, Newfoundland and Labrador | Kenmore | C970-415852 | N/A | Display has been going dim for a few years now but oven worked fine. Then all of a sudden nothing works on the oven only the oven light. Checked power to terminal block, 240 volts. checked power going to the board and seems ok. | Repaired |
West St. Paul, Manitoba | Frigidaire | CPEB30S8CC2 | N/A | Bake and Convection do not work. Broil does work. K2 open on board. Jumpered L1 and BA to test. Bake and convection did work when jumped. | Repaired |
St-barnabe-sud, Québec | Frigidaire | CPEB30S8CC2 | None | Bottom element not heating. Replaced element did not solve issue. Verified continuity on old element and shows continuity. Tested voltage on the leads. 120 on one lead and nothing on the other. Most likely culprit is the relay on the timer needs to be replaced. | Repaired |
toronto, Ontario | Frigidaire | cgeb27s7cb1 | F3 | upper element stays on after oven has reached required temperature. and F3 is displayed. Checked temperature probe,and reads 1087 ohms, when cold, appears to be OK, harness seems to be OK, no signs of shorting out. | Awaiting receipt of timer |
Medicine Hat, Alberta | Electrolux | | N/A | Bake element not working | Repaired |
Langley, British Columbia | Frigidaire | CGEB27S7CS1 | N/A | no heat on bake | Repaired |
Maple Ridge, British Columbia | Frigidaire | CGEB27S7AS1 | N/A | The oven still works but the broiler element will not heat up. I had the broiler element out of the oven and had it checked. The element is in good working order. When I called your company I spoke with Howard and he thinks the problem is in the timer. | Repaired |
Fort ST John, British Columbia | Frigidaire | CFEB786JGB3 | F1 & F3 | works normal ,then trips on F1, I removed the display ribbon then it tripped on F3. Normally tripping on F1 every time we use it. | Repaired |
Etobicoke, Ontario | Frigidaire | CPEB30S8AC2 | N/A | No heat to upper & lower element on bake,broil or convection settings! 220Vac to controller board-OK. Continuity test on both elements-OK. Thermal breaker reset-OK. Temp probe (1Kohm @ room temp)-OK. Checked all wiring-OK. | Repaired |
Montréal, Québec | Frigidaire | CGEB27S7CS1 | NOTHING | BAKE DOESN'T WORK
K2 RELAY DONT SWITCH (PIN E7) | Repaired |
Montréal, Québec | Frigidaire | cgeb27s7cs1 | N/A | Bake element only receiving 53 volts instead of 220v | Repaired |
Calgary, Alberta | Frigidaire | PLEB30S8CC or CPEB30S8CC | F3 | Heard a pop while cooking, and everything stopped working. Except the interior oven light when you open the oven door. Upon taking the oven apart, and having the breaker off and on, the clock started up, and then the F3 code appeared when pushing any oven controls. The Temp. sensor probe and wiring are testing fine. There is a burn mark between the 2 circuit boards. Hope you can fix it. | Beyond Repair |
Grimsby, Ontario | Frigidaire | CFEB386JGBI | F1 & F3 | Oven heats up but in short time give error code. Was F1 one time then gave F3. I replaced temperature sensor within the last 2 years. | Repaired |
Regina, Saskatchewan | Frigidaire | CGEB27S7CS1 | NONE | Appears to work except no power to lower bake element. Element OK, and broiler, convection OK. | Repaired |
Calgary, Alberta | Frigidaire | CPEB30S8CC2 | N/A | Everything works except the bake function (lower element). | Repaired |
Surrey, British Columbia | Frigidaire | CPEB30S8AC1 | no code occuring | Digital display intermittently goes dark and total loss of controls. If you bump it or close oven door it will sometimes regain display and controls.Loss of power can last for a few minutes up to several hours. At this point, display will not come on at all. | Repaired |
Chestermere, Alberta | Frigidaire | | N/A | no bake | Repaired |
Winnipeg, Manitoba | Frigidaire | CPEB30S8CC2 | No failure code | Bake element will not warm past 200 degrees | Repaired |
Saint-Ambroise-de-Kildare, Québec | Frigidaire | CGEB27S7CB2 | None | Sometimes 0.K but mainy time it is very long to reach the good
temperature (or not).
Temperature sensor (probe) was changed without amelioration. | Awaiting receipt of timer |
THUNDER BAY, Ontario | Frigidaire | CGEB27S7CB1 | NO BAKE, NO CONVECTI | NO BAKE, NO CONVECTION, BROIL WORKS | Repaired |
Fort Vermilion, Alberta | Frigidaire | CGEB27S7CB1 | NONE | Lower element not heating. Timer had a blackened and disconnected contact which I re-soldered. This did not resolve the issue. everything else works fine. | Awaiting receipt of timer |
Mount Pearl, Newfoundland and Labrador | Frigidaire | | N/A | bottom element not turning on/wrong oven temperture | Repaired |
Beaumont, Alberta | Frigidaire | CGEB30S8AS1 | no code | WHEN I TURN THE OVEN ON THE TEMPERATURE WILL NOT GO ANY HIGHER THAN THE DEFAULT OF 350'. I CAN MOVE THE TEMPERATURE LOWER, THE TIMER ALSO GOES OUT IF TRYING TO CHANGE OPERATION TYPES LIKE CONVECTION TO NORMAL BAKE. | Awaiting receipt of timer |
St-Lazare, Québec | Frigidaire | | f1 f3 | Stops heating | Awaiting receipt of timer |
BIBLE HILL, Nova Scotia | Frigidaire | cgeb275 | N/A | won't heat Brown | Repaired |
Rockwood, Ontario | Frigidaire | CPEB30S8CC2 | N/A | Bake element won't work. | Awaiting receipt of timer |
Calgary, Alberta | Frigidaire | CFEB386JGB2 | N/A | Display is dim and very hard to read. | Repaired |
Mont-Tremblant, Québec | Frigidaire | CGEB27S7CS1 | NOTHING | FOUR CHAUFFE PAS, NO HEATING | Repaired |
BIBLE HILL, Nova Scotia | Frigidaire | CGEB27S7CB1 | N/A | oven won't heat
Customer - Samantha Gallant | Repaired |
Montreal, Québec | Frigidaire | cpeb30s8cc2 | N/A | bottom element not working,top element is working | Repaired |
St. Catharines, Ontario | Frigidaire | CFEB389WEC7 | F1 and F3 | F3 code appears every once in a while; occasional F1 code appears; replaced temp. sensor probe but codes still appeared. Checked sensor independently - it showed a resistance reading of 1080 ohms (at room temp); checked sensor while connected to wire harness at EOC end - it also showed 1080 ohms. | Repaired |
saint-jerome, Québec | Frigidaire | cgeb27s7asi | no failure code | the bake element does not working , the broil element working | Repaired |
Peachland, British Columbia | Frigidaire | CGEB27S7C | N/A | oven is a convection wall-mounting type
no error codes, display seems to be fine.
oven bake heats up VERY slow and doesn't get fully hot
on bake cycle - lower bake element stays cold, back convection element stays cold, upper broil element gets warm
on convection cycle - lower bake element stays cold, back convection element stays cold, fan works and seems fine
on broil cycle - lower bake element stays cold, back convection element stays cold, upper broil element gets red hot | Repaired |
Richmond, British Columbia | Electrolux | CGEB27S7CB1 | N/A | Oven does not heat. Clock works but when oven button pressed it shows the temperature selected but does not heat then displays 100F oven on. A clicking sound can be heard but no heating is noted. | Repaired |
calgary, Alberta | Frigidaire | cgeb27s7cb1 | N/A | I will send the faulty timer after I receive the reconditioned one from you for the credit.
thank you | Repaired |
Delta, British Columbia | Frigidaire | CPEB30S8AC2 | N/A | Oven doesnt get avove 350 degrees | Replaced with new in-stock timer |
LA TUQUE, Québec | Frigidaire | CF786JGS2 | N/A | tEMPERATURE DISPLAY IS NOT LISIBLE | Awaiting receipt of timer |
Coquitlam, British Columbia | Frigidaire | CGEB27S7CB1 | N/A | heating up slowly (sometimes) Relay element is suspect | Replaced with new in-stock timer |
Queensville, Ontario | Frigidaire | cgeb30s8cs1 | N/A | Power failure in area due to car accident when power was restored the wall oven control board would not light up. I suspect a transformer failure due to windings discoloured on one side. The transformer has been replaced previously after as similar occurrence. | Awaiting receipt of timer |
gatineau, Québec | Frigidaire | cfeb786jgs2 | N/A | vari broil not working | Repaired |
BIBLE HILL, Nova Scotia | Frigidaire | CGEB27S7CS1 | F1 | F1 code | Replaced with reconditioned timer |
Victoria, British Columbia | Frigidaire | CGEB2757CB1 | N/A | oven botton element will not come on when using BAKE but top element will.
tried new element but that is not the problem. Apliance repairman said needed new timer | Replaced with new in-stock timer |
Port Hardy, British Columbia | Frigidaire | cgeb27s7cb1 | N/A | oven broiler not functioning, but tests okay. no burnt wires. tester points to control panel problem | Repaired |
Richelieu, Québec | Frigidaire | oven | N/A | Base element not heating more than 100 degre | Awaiting receipt of timer |
CHICOUTIMI, Québec | Frigidaire | CGEB27S7CB1 | NONE | THE DISPLAY ON MY CONTROL PANEL LIGHT NORMALY, WHEN I SET THE TEMPERATURE FOR THE BOTTOM ELEMENT I EAR THE DECLIC BUT I DON'T HAVE HEATER, SO FOR THE TOP ELEMENT HE WORK SO GOOD WHEN I PUT TO BROIL. I VERIFIED THE BOTTOM ELEMENT WITH A MULTIMETER AND I HAVE A CONTINUITY. I'AM NOT SURE BUT I THINK IT'S THE CONTROL PANEL WHO IS DEFECT BECAUSE I WATCH ON INTERNET FORUM AND OFTEN THIS IS THE PROBLEM.
THANK YOU | Repaired |
Laval, Québec | Frigidaire | CFEB786JGB | N/A | The display does not light up. | Replaced with new in-stock timer |
Montréal, Québec | Frigidaire | Frigidaire professional series (2002) | No failure code. | We call for service and they said it's the timer. The top element work but not the bottom one and the one at the back (middle). There is no heat for those two element. When we start bake there is little heat because there is a cycle that also use the top element but it gain like 50oC in one hour. | Awaiting receipt of timer |
Trois-Rivieres, Québec | Frigidaire | CPEB30S8A | N/A | all off | Awaiting receipt of timer |
Chicoutimi, Québec | Frigidaire | CGEB27S7CB1 | NONE | The bottom element didn't work . When i click on the bake button, i can see on the wallplate bake is on and i can set the temperature and i can hear the click inside the control but the element refuse to heat. If i cancel the bake operation and start broiling. I can see on the wallplate broiling is on, then hearing the click inside the control and the broil element heat correctly. After (contact us) by e-mail, your answer was : In order to confirm the diagnosis,disconnect the wire from BA put it on BR and activate broil.Ir the bake element comes on then you know that the board is bad. The result is : Exactly like you said, the bake element come on, so the board is bad. Can you repair my board please. Thank You ! | Repaired |
Belle River, Ontario | Frigidaire | CFEB786JGS2 | N/A | Already sent this info in the timer package | Repaired |
Montréal, Québec | Frigidaire | Frigidaire professional series (2002) | No failure code. | We call for service and they said it's the timer. The top element work but not the bottom one and the one at the back (middle). There is no heat for those two element. When we start bake there is little heat because there is a cycle that also use the top element but it gain like 50oC in one hour. | Awaiting receipt of timer |
Lac-kenogami, Québec | Frigidaire | cgeb27s7as1 | N/A | oven only works in grill mode | Beyond Repair |
Hantsport, Nova Scotia | Kenmore | c970 418826 | no code | Oven will not increase in heat after the setting has been selected. The display is held at a constant 100 degrees. There is a clicking noise, indicating the oven wants to increase in heat, but something will not let it. | Repaired |
MONTRÉAL, Québec | Frigidaire | CFEB786JGB2 | N/A | BEFORE FAILURE, THE CLOCK TIME WAS RUNNING LOWER THAN THE REAL TIME. AFTER IT CLOSE TOTALLY. WHEN I PUSH THE BAKE BUTTON, I HEARD A SOUND, LIKE OPENING BUT AFTER 2 SECONDS I HEARD A SECOND SOUND AS IT CLOSE. | Awaiting receipt of timer |
St-Lazare, Québec | Frigidaire | cgeb27s7cs1 | N/A | Only broil works, bake and convection don't. Repair tech came and said it was the issue... | Repaired |
EMBRO, Ontario | Electrolux | CGEB27S7CB1 | N/A | Bottom element does not come on. Everything else works.
Please repair & return if possible.
I will return the (replacement) part I received on Oct 5 after I install the repaired item.
(re Invoice 104908) | Repaired |
KINGSTON, Ontario | Frigidaire | CFEB786JGS3 | NONE | LED DISPLAY IS GETS DIMMER OVER TIME. CANNOT READ IT DURING THE DAY. | Awaiting receipt of timer |
Burrnaby, British Columbia | Frigidaire | CPEB30S8CC1 | N/A | The upper element in the oven is working fine but Lower element in the oven is not working.
Technicain suggested that the timer is not working and need to be replaced | Replaced with reconditioned timer |
Port Hardy, British Columbia | Frigidaire | cgeb27s7cb1 | N/A | oven broiler not functioning, but tests okay (new broiler element did not fix problem). No burnt or loose wires. Tester points to control panel problem. | Repaired |
Nelson, British Columbia | Frigidaire | CPEB30S8CC2 | N/A | Oven lower element does not work | Repaired |
Whitby, Ontario | Frigidaire | Electrolux | N/A | I have "Broil" but no "Bake" and no "Convection" Heat. I have checked the fuses. I have replaced the bottom element. An appliance repair man told me it has no power from E7 to E9. | Repaired |
Pembroke, Ontario | Electrolux | cgeb27s7cs1 | none | Oven intermittently comes up to temperature and if it does does not always stay at temp. When working element turns read and oven heats quickly. When it doesn't it sometimes comes up slowly, but not always. | Repaired |
Prince Albert, Saskatchewan | Frigidaire | CGEB27S7CB1 | none | both Bake and Broil elements not heating.
Convection fan, door lock working, and light working | Replaced with reconditioned timer |
North Vancouver, British Columbia | Frigidaire | CPEB30S8CC2 | N/A | Bake & convection bake relays not working | Awaiting receipt of timer |
Brandon, Manitoba | Frigidaire | | N/A | Not applicable | Replaced with new in-stock timer |
Grand Bay, New Brunswick | Frigidaire | cgeb27s7cb1 | none | all functions of the timer work except the bake and convection elements dont come on, there is no 120v when the bake element is suppose to be working on the output of the control card for this element. The oven actually heats up to temperature with the broil element. | Replaced with new in-stock timer |
Victoria, B.C., British Columbia | Frigidaire | CGEB2757CB1 | N/A | oven bottom element stays cold, top element heats up to 240. Appliance repairman did say a new timer was needed. | Replaced with new in-stock timer |
BIBLE HILL, Nova Scotia | Frigidaire | cgeb275 | N/A | won't heat | Repaired |
Saint John, New Brunswick | Frigidaire | cgeb27s7cs1 | N/A | | Repaired |
Calgary, Alberta | Frigidaire | CFEB789JGS3 | F1 and sometimes F3 | We first started getting errors with the oven a couple of years ago when it occasionally would give us an F3 error while using the broil function. If we'd press cancel and try again, the error would often come back as either an F3 or an F1. After the initial period the errors came without using the broil and with time the F1 became more common and towards the end F1 was the only error code coming up.
Before we decided to disconnect the oven all together we started getting the F1 immediately when turning the oven on and even when the oven wasn't in use, e.g. in the middle of the night or when we weren't home at all.
At this point we haven't used the oven in a couple of months and the power for it has been disconnected. | Repaired |
KELOWNA, British Columbia | Frigidaire | CFEB786JGB | clock is blank | clock is blank | Repaired |
Durham, Ontario | Electrolux | CPEB30SCC2 | none | After a auto clean of the oven. The oven is no longer heating up beyond about 80C. | Repaired |
calgary, Alberta | Frigidaire | cgeb27s7cb1 | N/A | does not work on broil or bake | Repaired |
Drummondville, Québec | Frigidaire | CGEB27S7CB1 | F-1 | Code F-1 with a bip sound. | Awaiting receipt of timer |
Brownsburg Chatham, Québec | Frigidaire | cgeb27s7as1 | N/A | oven bake and convection will not heat..elements are OK. | Awaiting receipt of timer |
Mayne Island, British Columbia | Frigidaire | CGEB27S7CB1 | n/a | The bake relay is faulty. Also the display is dimming. | Repaired |
Glace Bay, Nova Scotia | Frigidaire | CGEB30S8CS1 | None | No heat on broil or clean. Service man said it was the control board. | Replaced with reconditioned timer |
Port Coquitlam, British Columbia | Frigidaire | CBEG30S8CB1 | BAKE will not heat - | Bake will not heat properly (I beleive convection is not heat too, but fan works). No voltage to burners. Repair tech says one relay is not working. | Repaired |
St Basile le Grand, Québec | Frigidaire | cgeb27s7cb1 | N/A | timer is burn | Awaiting receipt of timer |
Aldergrove, British Columbia | Frigidaire | CPEB30S8CC2 | N/A | Lower heating element is no working. There is no power supplied to element. | Awaiting receipt of timer |
vancouver, British Columbia | Frigidaire | cgeb27s7cb1 | N/A | bake element does not heat. | Repaired |
Cookshire, Québec | Frigidaire | CFEB786JGS | F1-F3 | Get error code F1 or F3 after couple minutes and won't turn back on. Shutting breaker off & back on will solve problem then error code returns after couple minutes. Checked oven probe sensor and reads resistance of 1080ohm at room temperature. | Repaired |
waterloo, Ontario | Frigidaire | CPEB30S8CC2 | N/A | does not heat, show power on dis play if try to change any thing it wont do kind of frozen | Beyond Repair |
St. John's, Newfoundland and Labrador | Frigidaire | CPEB30S8AC2 | F1 intermittent | oven elements not heating | Awaiting receipt of timer |
Richmond, British Columbia | Frigidaire | CGEB27S7CB1 | N/A | Oven won't heat up, control panel clicks, broil works | Repaired |
Three Hills, Alberta | Frigidaire | CFEB786JGS2 | N/A | Unable to read display. unable to control temperature. stays at one temperature | Awaiting receipt of timer |
Jemseg, New Brunswick | Frigidaire | CGEB27S7CB1 | none were displayed | Had a appliance repair man in to inspect, elements were not heating up. Repair man checked over everything and found there was no damage to any parts that just the oven timer/clock was not putting out power to the relays. He checked and found that frigidaire does not make these parts anymore and there are no substitutes available. | Awaiting receipt of timer |
Saskatoon, Saskatchewan | Frigidaire | CGEB2757CS1 | none | The broiler burner stopped work. A repair technician diagnosed failure of the timer unit. | Repaired |
l'Étang du Nord, Québec | Electrolux | | N/A | Element du bas ne chauffe pas | Repaired |
Alexabdria, Ontario | Frigidaire | CGEB27S7CS1 | N/A | all digits completely lit up, push controls do not work | Replaced with reconditioned timer |
North Bay, Ontario | Frigidaire | | N/A | temperature display is so light can't be read | Awaiting receipt of timer |
Chetwynd, British Columbia | Electrolux | CGEB27S7CS1 | none | Bake element does not heat. Broil element cycles as per program. No error codes are evident. Did notice an internal scorch mark top left of display after timer was removed. | Repaired |
sudbury, Ontario | Frigidaire | | F1 F3 | F1 AND F3 ALARM | Awaiting receipt of timer |
Caledon, Ontario | Electrolux | CFEB389WEC8 | F1 | F1 ERROR CODE WAS INTERMINTENT FOR ABOUT 2 MONTHS.
F1 ERROR CODE COMES UP EVERYTIME I USE OVEN | Repaired |
Richards Landing, Ontario | Frigidaire | | F1 | Came home to find oven beeping and displaying -f1- code. Turned off breaker overnight to see if reset would help. No more error code, but it's as though the down button is sticking on. Won't allow any functionality. | Awaiting receipt of timer |
Victoria, British Columbia | Frigidaire | CGEB27S7A | F3 | oven heats up then F3 error code appears and will not reset | Repaired |
Brossard, Québec | Frigidaire | Gallery | N/A | F-1 code,stop heat | Replaced with reconditioned timer |
Spruce Grove, Alberta | Frigidaire | CGEB30S8CB1 | N/A | Lower (bake) element not working. Fault diagnosis confirms that the element is working - only the bake circuit is failed. All other control functions are working. | Repaired |
Hope, BC, British Columbia | Frigidaire | CGEB27S7Cb1 | n/a | bake and convection functions not working
elements are fine
broil function works fine
checked for voltage to element, was none
took apart EOC and found burnt solder on bake element relay. repaired and stove worked once but not working again | Replaced with reconditioned timer |
Edmonton, Alberta | Frigidaire | cgeb27s7cs1 | N/A | Nothing works in oven | Repaired |
Repentigny, Québec | Frigidaire | CPEB30S8CC1 | F1 | Top element works, but bottom element does not.
Also receive F1 error code occasionally. | Repaired |
Okanagan Falls, British Columbia | Frigidaire | CPEB39S8CC2 | no code appeared,onl | on the key pad as it is a touch pad:right hand side timer and clock work, scroll up down- work
left hand side of the touch pad the oven light works. Broil and Bake do not work | Awaiting receipt of timer |
Oak Bay, New Brunswick | Frigidaire | CGEB27S7CB1 | Broiler does not wor | Broiler does not work. | Repaired |
Cayuga, Ontario | Frigidaire | CGEB27S7CS1 | N/A | Lower element not working, on bake cycle broiler comes and off but no power from output "BA" to lower heating element at any time. Suspect relay K2 not functioning properly. | Repaired |
Campbellville, Ontario | Frigidaire | CGEB27S7AB1 | N/A | Oven stopped working while baking. Removed timer and soldered one connection. Oven worked for a few weeks. Then, turned on intermittently a few times. First only the top element came on. Now oven will not turn on at all. Noticed one relay looks to have overheated. | Repaired |
dollard-des-ormeaux, Québec | Frigidaire | Frigidaire wall oven CPEB30S8AC1 | F3 and F1 | After working about 10-15 min, F3 message and F1 sometimes. Oven will beep intermittently until we press on cancel button. | Repaired |
Saskatoon, Saskatchewan | Electrolux | CPEB30S8CC2 | N/A | No power to bake element. | Repaired |
Gatineau, Québec | Frigidaire | CGEB27S7CB2 | Unknown | Tenant started self-clean with over door open, then let the self clean program run until the end. The oven stayed in locked position, fan runs constantly (while door open) and electronic control no longer responds to anything. Tried turning breaker off then on, keeping it off for 30 minutes and more, but oven status remained unchanged once back on. | Timer inspected, no repairs necessary |
Barrie, Ontario | Frigidaire | CGEB27S7CB1 | F1 | Try to start oven and it comes up with F1 code | Repaired |
Dowling, Ontario | Frigidaire | cpeb30s8cc2 | ????? | bottom element dont work and it checks ok | Awaiting receipt of timer |
Montréal, Québec | Frigidaire | cpeb30s8cc2 | No LED Display | No LED Display. If several buttons are pressed simultaneously, the "On" sign flickers quickly and disappears and a light electrical buzz sound can be heard coming from the timer.
Touch pad unresponsive.Oven can only be turned on and off with the electrical breaker (or by removing the power plug).
When power plugged oven will broil automatically, without any action from our part. No bake.
Before being totally broken, the oven could stop working from time to time (no more LED display, touch pad unresponsive), but switching the breaker was sufficient to make it work again, until now. | Beyond Repair |
WEST VANCOVER, British Columbia | Frigidaire | CPEB30S8CC2 | N/A | The lower burner in the oven does not work, but the broiler works. Apparently the cooling fan is also not functioning. | Repaired |
Mount Albert, Ontario | Frigidaire | CFEB386JGS2 | N/A | The connection burnt off where oven connects to the wire from the panel. After it was repaired the was no power to the bake element or convection. Broil element seems to work. Elements test good. Tried replacing the bake relay as one of the pins seemed to be burnt off.Still didn't work. | Repaired |
Wolfville, Nova Scotia | Electrolux | Frigidaire | N/A | Our wall oven stopped working in the midst of cooking a meal. The light comes on when the door is open and the fan runs (have to shut the breaker off or the fan runs continuously). Nothing else on the system seems to work (all touch sensors and nothing shows on the panel when power is on). | Repaired |
Amherst, Nova Scotia | Frigidaire | Frigidaire Gallery/CGEB27S7AS1 | F3 | The timer had intermittent faults (F4 and F3) for the past year and would clear if we powered the unit down and then re-powered it and them reprogramed the time but now the timer shows an F3 code constantly and the oven will not function. | Repaired |
Chetwynd, British Columbia | Electrolux | CGEB27S7CS1 | none | Bake element does not come on - broil, top element does cycle. Pulled bake element out and tested had 25K resistance - element should be good. | Repaired |
L'Ange-Gardien, Québec | Frigidaire | cfeb389wec8 | F-1 and F-3 | The oven is often stopping and F-3 code is showing. Some times, we also have F-1. | Repaired |
Calgary, Alberta | Frigidaire | CPEB30S8AC1 | F1 and F3 | The Oven turns on, but once it reaches a high temperature, it beeps and F1 or F3, usually F3 is displayed. Ounce that happens we just turn it off. been like this for about a month. | Awaiting receipt of timer |
Tillsonburg, Ontario | Frigidaire | CPEB30S8AC1 | F3 | Will try to heat but gives an F3 at about 220 degrees.Clicks loudly as it increments heat by 5 degrees. | Replaced with reconditioned timer |
kitchener, Ontario | Frigidaire | cpeb30s8cc2 | N/A | Not working | Awaiting receipt of timer |
Québec, Québec | Frigidaire | CGEB27CS1 | N/A | BAKE DON'T WORK | Awaiting receipt of timer |
Brechin, Ontario | Frigidaire | CPEB30s8CC2 | N/A | Burnt relay | Beyond Repair |
Winnipeg, Manitoba | Frigidaire | CGEB30S8AB1 | None | My bake element stopped working with no 'F' error code. I swapped out the broil wire and bake wire on the EOC, and the bake element glowed red. | Repaired |
Richmond, British Columbia | Frigidaire | CGEB27S7CB1 | N/A | Broiler works. Oven won't heat. control unit clicks. | Repaired |
KAMLOOPS, British Columbia | Frigidaire | CFEB789WFC1 | F3 & DIMM DISPLAY | F3 AND DIM DISPLAY | Repaired |
Anglemont, British Columbia | Frigidaire | CGEB27S7CB1 | N/A | no voltage to broil element there is voltage to the relay and I hear it click but no output to the element | Repaired |
Saskatoon, Saskatchewan | Frigidaire | CGEB27S7 CB2 | N/A | Oven will not hold temp when baking // broil option works great | Repaired |
St-Stanislas-de-Champlain, Québec | Frigidaire | Gallery Series | N/A | When the oven is powered all symbols and digits of the LCD are ON. It's also impossible to control anything on the oven. | Beyond Repair |
glen haven, Nova Scotia | Frigidaire | cgeb27s7cb1 | N/A | lower back element won't work | Repaired |
L'Ange-Gardien, Québec | Frigidaire | CFEB389WEC8 | F1 & F3 | Poor baking power. Sometime, having hard time reaching temperature and F1 & F3 code appears. | Repaired |
Brentwood Bay, British Columbia | Frigidaire | CGEB30S8CB1 | N/A | Heard a pop, noticed panel was completely blank. Oven light works, no circuits are or were tripped, just timer model dead. Notice a small black spot on the upper left hand corner of the class module for the display. | Beyond Repair |
Repentigny, Québec | Frigidaire | CPEB30S8CC1 | F1 | TOP ELEMENT WORKS,BUT BOTTOM ELEMENT DOES NOT..I occasionally receive the "F1" error code. | Repaired |
Neebing, Ontario | Frigidaire | CFEB386JGS2 | none | dead | Repaired |
Ariss, Ontario | Frigidaire | NF11213218 | F1-F3 | Temp of in wall oven will raise to about 360 F then shut down with either an F1 or F3 code. Temperature probe was replaced but still same issue. | Repaired |
Red Deer, Alberta | Frigidaire | 27' CGEB27s | none | Bottom burner - bake option, convection options are not heating - no heat to burner. Over will not get above 150 degrees. Top element - broil still works fine. All buttons seem to be working fine. Problem seems to have occurred either immediately after, or soon after a oven self-clean cycle. | Repaired |
Washago, Ontario | Frigidaire | CGEB30S8CB1 | no failure code | Everything works except bake element. Bake element tested ok and I even tried a new element. | Repaired |
burnaby, British Columbia | Frigidaire | | N/A | No heating. | Replaced with reconditioned timer |
Brossard, Québec | Frigidaire | CGEB27S7CB1 | no failure code | it's not heating anymore.
first Broil went off and a couple of months later bake is not working neither.
I checked elements: it's fine
I checked relays: BR BA L1 and the tests failed. | Repaired |
Calgary, Alberta | Frigidaire | - | - | Broil works. Heat does not. Checked circuit with voltage meter and it delivers no power to bottom element. | Repaired |
Port Hardy, British Columbia | Frigidaire | 3GEB27S7CS1 | None | Bake and convection not working. No power from Ba on board when bake activated | Repaired |
Bonny RIver, New Brunswick | Kenmore | Unknow | None | Timer kicks out when oven is in use and when and it is not in use. When reset it could last for a week or for five minutes. there is no reason to it. | Awaiting receipt of timer |
Saskatoon, Saskatchewan | Frigidaire | CFEB786JGS2 | N/A | Timer/Clock does not light up. Function buttons relating to timer do not beep when pressed. All other function buttons beep when pressed. Both elements work, as does the oven light. | Repaired |
Mississauga, Ontario | Frigidaire | CFEB789WFC1 FRIDGIDAIRE | N/A | The elements are not receiving power. We suspect the relays (Black Cubes) are not working. | Repaired |
Eel river crossing, New Brunswick | Frigidaire | Gallery | N/A | no | Awaiting receipt of timer |
Sydney, Nova Scotia | Frigidaire | CPEB30S8CC1 | F1 and F3 | Burn mark in upper left front corner of timer display | Replaced with reconditioned timer |
Surrey, British Columbia | Frigidaire | | none | no function/no display. assuming no power | Repaired |
Ochre River, Manitoba | Frigidaire | CGEB30S8C | N/A | Broil works. No heat from convection or main element. Elements tested and not the problem.
1 relay replaced that controls both convection and main element and not the problem. | Awaiting receipt of timer |
Wawa, Ontario | Frigidaire | CGEB27S7C | f 1 | The problem has been intermittent but now we cannot get the oven to heat. | Repaired |
elkford, British Columbia | Frigidaire | | N/A | All 3 elements dont work. Narrowed it down to the 2 relays on the back but need whole timer | Awaiting receipt of timer |
calgary, Alberta | Frigidaire | | N/A | dim display | Awaiting receipt of timer |
Napanee, Ontario | Frigidaire | | N/A | The oven does not heat up | Repaired |
Winnipeg, Manitoba | Frigidaire | | N/A | No display timer is buzzing had power surge | Awaiting receipt of timer |
Belleville, Ontario | Frigidaire | CPEB30S8CC2 | N/A | This is the 2nd time my 2004 Oven has had the problem of bottom element not heating. Element appears fine and Sears service replaced the timer in 2008. Now he says timer is shot again but new ones are NLA. | Beyond Repair |
BLIND BAY, British Columbia | Frigidaire | 318030038-MEM-A-086 | N/A | Both heating elements don"t work,but are not burnt out. | Awaiting receipt of timer |
Hudson, Québec | Frigidaire | | DEAD | when on autocleaning mode, the timer went non responsive (we still have visual) ; door is locked (still even after shutting down electricity and bringing it back) ; cooling fan is running and the autocleaning cycle seems to have never gone on | Awaiting receipt of timer |
Vaughan, Ontario | Frigidaire | CPEB30S8CC2 | N/A | BOTTOM HEATING ELEMENT IS NOT WORKING | Awaiting receipt of timer |
Selkirk, Manitoba | Frigidaire | CGEB27S7CB1 | not showing any | oven stopped heating to proper temperature, and took a long time to heat at first, then stopped heating altogether. bottom element stopped working first, then broiler element also stopped. clock and oven light continued working. no failure codes ever showed. | Repaired |
Campbellcroft, Ontario | Frigidaire | CPEB30S8CC2 | none | low voltage to the bake element, broil works okay. | Repaired |
St.Albert, Alberta | Frigidaire | CGEB30S8AB1 | N/A | traditional baking function will not work. Convection baking and broiling still function properly. | Repaired |
sarnia, Ontario | Frigidaire | cfb786jgs2 | N/A | blank screen | Repaired |
elliot lake, Ontario | Frigidaire | cfeb786jgs3 | N/A | Digital oven temp was dull put on self clean cleaned oven ok turned oven on after heard a puff sound ditial went blank clock went blank oven light still works can it be repaired thanks | Beyond Repair |
elliot lake, Ontario | Frigidaire | cfeb786jgs3 | N/A | Digital oven temp was dull put on self clean cleaned oven ok turned oven on after heard a puff sound ditial went blank clock went blank oven light still works can it be repaired thanks | Beyond Repair |
Cochrane, Alberta | Electrolux | cgeb27s7cs1 | none | Oven won't heat up on bake or convection bake. Broil seems to work ok. | Repaired |
Maple Ridge, British Columbia | Frigidaire | CFEB389WEC7 | F1 and F3 | Oven works using bake if used 20 mins or less. If used longer then get F1 or F3 message have seen both. Then oven shuts off. Can sometimes cancel and reset and will work for a few more minutes but then will send F1 or F3 message again and shut off. Recently it would not turn back on after I cancelled. Shut off at breaker and could reset but then error message again shortly after. Recently tried the convection method and ran for 30 min with no error message. Not sue if I would have gotten the error msg if I ran for longer than 30 min. Sensor probe has been tested and is functioning properly. | Repaired |
barrie,ontario, Ontario | Frigidaire | cfeb786jgb331801070 | f3 | DISPLAY LIGHT DIM DIFICULT TOREAD,OVEN UP FOR 20 MINUTES SHUTS DOWN AND BEEPS DISPLAYING F3 | Repaired |
Timmins, Ontario | Frigidaire | CGEB27S7CS1 | N/A | Bake element does not work
Convection element does not work
I checked the heat sensor and it registered 1180. I checked elements for continuity and there was continuity (about 27 ohms on bake element, convection element 23 ohms). | Repaired |
Thornlea, Trinity Bay, Newfoundland and Labrador | Frigidaire | CGEB27S7CB1 | N/A | no power being delivered to the elements. everything else works, you can still hear the oven clicking like the temp. is rising. service man said it was the thermal switch/breaker but replaced that one and when I changed it out I tested the old one and it was still good, so he wasted my time and money. so I tested everything else with the meter and everything seemed o.k. except the temp probe, would that cause this problem, if not I guess it is the timer. Tried to call you guys today but got the machine and left a message. the oven isn't showing any codes at all. BEFORE YOU GUYS SEND ME ANYTHING CAN YOU LET ME KNOW IF YOU GUYS THINK THAT THIS IS THE PROBLEM OR NOT | Awaiting receipt of timer |
Tsawwassen, British Columbia | Frigidaire | CFBEB389WEC2 | Blank | No Power to timer, blank face. | Repaired |
Williams Lake, British Columbia | Frigidaire | CGEB27S7CS1 | no code | Broil worked. Bake and convection bake did not work. Convection fan would run.
When control turned onto bake or convection a click could be heard in the control after a few seconds. | Repaired |
Calgary, Alberta | Frigidaire | CGEB27S7CS1 | F1 | Fan keeps running And the door is locked. | Repaired |
New Hamburg, Ontario | Frigidaire | CGEB27S7CB1 | None | Main oven element will not turn on or heat up the oven. We had a repair man test the oven and he determined that the element was ok, and therefore isolated the problem to the control panel/timer. | Repaired |
Cambridge, Ontario | Frigidaire | | N/A | Bake/Convection Relay not working on oven and Clock not working. Showing Zeros. | Awaiting receipt of timer |
Burnaby, British Columbia | Frigidaire | CGEB27S7CB1 | N/A | Failure on broiler element | Repaired |
Richmond, British Columbia | Frigidaire | CPEB30S8CC2 | F1 | Will not work keep beeping | Awaiting receipt of timer |
Seddons Corner, Manitoba | Frigidaire | CGEB27S7CB1 | N/A | Bake and convection element not working | Awaiting receipt of timer |
Bridgewater, Nova Scotia, Nova Scotia | Frigidaire | CGEB27S7CS1 | circuit board issue | control panel will not engage bottom element | Awaiting receipt of timer |
Miscouche, Prince Edward Island | Frigidaire | CGEB27S7CB1 | N/A | Oven does not reach temperature. sometimes it works but most times it doesnt. | Repaired |
Surrey, British Columbia | Frigidaire | CPEB30S8CC2 | F 1 | Oven does not heat up properly, very slow and only to a low temperature. | Repaired |
Tsawwassen, British Columbia | Frigidaire | Fridgidare | blank | Blank display, timer not working. | Repaired |
Hamilton, Ontario | Frigidaire | CFEB386JGS2 | N/A | Clock display was going dim then totally out. | Repaired |
Camrose, Alberta | Frigidaire | CPEB30S8CC2 | N/A | Bake element not working | Awaiting receipt of timer |
Napanee, Ontario | Frigidaire | | N/A | The oven wont heat up. | Repaired |
Calgary, Alberta | Frigidaire | CPEB30S8AC1 | N/A | Convection Bake does not work, just regular bake | Repaired |
Galiano Island, British Columbia | Frigidaire | CPEB30S8CC1 | none | Set up the timer clock. Put oven into self-clean mode, and the relay output contacts blew. When I purchased this oven used, I tried the oven out. Oven turned on a heated to the correct temperature in about 10 minutes. All lights on as normal, display indicated all was well. Brought it home, set the clock, pressed the button for self clean, and bang! | Beyond Repair |
Calgary, Alberta | Frigidaire | CpEB30S8AC1 | N/A | Convection Back mode does not work, regular bake mode does work | Repaired |
Combermere, Ontario | Frigidaire | CGEB2757CB1 | N/A | Oven does not heat up from the bottom element. Repair man says board (timer )needs repair.
Thank you,
R McLean | Repaired |
Sydney, Nova Scotia | Frigidaire | CPEB30S8CC1 | F1 | Oven works for awhile and then an F1 code will appear, reset the oven and it will work again for a period then F1 appears again with some F3 codes. The temperature sensor (F3) was replaced with a new unit and tests fine at 1089 ohms. The old one tested fine as well. | Repaired |
St Prosper, Québec | Frigidaire | CFEB786JGS2 | N/A | emet un bruit continue | Awaiting receipt of timer |
Hamilton, Ontario | Electrolux | galler series | N/A | Lower heaqt element will not come on, broiler unit works fine but can't be controlled | Repaired |
North View, New Brunswick | Electrolux | CGEB30S8CS1 | N/A | Oven will not maintain set heat | Awaiting receipt of timer |
Delta, British Columbia | Frigidaire | CGEB30S8CB1 | N/A | Heats to about 350 then stops intermittent | Repaired |
Wembley, Alberta | Electrolux | cgb30s8cs1 | ?? | no heat on convection and bake, oven heats up in an hr or so do to the broil clicking on and of every 2 or 3 minutes | Repaired |
Steinbach, Manitoba | Frigidaire | N/A | N/A | blank | Repaired |
Pierrefonds, Québec | Frigidaire | CGEB27s7as1 | N/A | fixed once before for oven relay. Now broil is not working and mayeb a problem with convection (might be external relay or motor ... not sre until take apart) | Awaiting receipt of timer |
Steinbach, Manitoba | Frigidaire | unavailable | N/A | Blank | Repaired |
Cornwall, Ontario | Frigidaire | CGEB27S7CS1 | N/A | Bake element does not turn on . Output from the relay is not working. For testing I swapped the output with the Broil relay on the circuit board and the Bake element heated up . I suspect the bake relay on the circuit board is faulty. | Repaired |
Laval, Québec | Frigidaire | CFEB786JGB2 | F1 has appeared one | Fan is always working
The door is locked
Unable to use the oven (bake or grill) | Repaired |
Montreal, Québec | Frigidaire | CGEB30S8CS1 | none | oven will not heat past 100. broiler (top element) works. | Repaired |
Chateauguay, Québec | Frigidaire | CGEB27S7CS1 | none | For a few days only the broil worked, then the control flashed and smoked and nothing worked after. The three elements and fans have been verified, but nothing else. | Awaiting receipt of timer |
Langley, B.C., British Columbia | Frigidaire | cpeb30s8ac2 | N/A | the broiler doesn't work | Awaiting receipt of timer |
Wembley, Alberta | Electrolux | cgb30s8cs1 | ?? | no heat on convection and bake, oven heats up in an hr or so do to the broil clicking on and of every 2 or 3 minutes | Repaired |
Quebec, Québec | Frigidaire | cpeb30s8cc2 | N/A | Broil element (no Element,broil ,2750 W) not working, element has been checked and is ok. the clean program and broil not working, that is because the Relay (no 318112701) isfailed | Awaiting receipt of timer |
Vancouver, British Columbia | Frigidaire | PLEB30S8CC | bake relay | BAKE ELEMENT DO NOT WORKE. | Awaiting receipt of timer |
Luskville, Québec | Frigidaire | | N/A | convection, broil, bake will not work | Repaired |
Edmonton, Alberta | Frigidaire | CGEB30S8CB1 | No code. | Bake element of oven will not heat up. Element has been tested for resistance and according to other internet posts, it is well in spec.
Voltage across bake element terminals is around ~50 volts whereas the voltage across the broil element is 240V when the oven is on.
Broil element will heat up without issue. | Repaired |
North Vancouver, British Columbia | Frigidaire | CPEB30S8CC2 | N/A | Relay that controls bake element is burned out. | Awaiting receipt of timer |
Halfmooon Bay, British Columbia | Frigidaire | cgeb27s7cb1 | N/A | bake element not working broil etc does work | Repaired |
Deep River, Ontario | Frigidaire | cpeb30s8cc2 | N/A | bake will not work broil works ok | Replaced with reconditioned timer |
elliot lake, Ontario | Frigidaire | cfeb786jgs3 | N/A | Digital oven temp was dull put on self clean cleaned oven ok turned oven on after heard a puff sound ditial went blank clock went blank oven light still works can it be repaired thanks | Beyond Repair |
Cochrane, Ontario | Frigidaire | CGEB27S7CS1 | none | Bake and convection not functioning. Broil functioning. | Repaired |
Port Mouton, Nova Scotia | Frigidaire | CPEB30S8CC2 | F3 | Bake/Convection not working. Broil Working.
No 240V on BA relay. Changed out relay.
Now getting F3
about 1200 ohms on sensor
figure it's the EOC | Repaired |
PORT HASTINGS, Nova Scotia | Frigidaire | CGEB30S8CB1 | NO FAILURE CODE | No display on timer at all. Service repair man said there was power coming to the timer but no visible signs of timer display.
Hopefully you will be able to repair this unit.
Thank You
Any questions Please call 902-625-0096 | Beyond Repair |
Didsbury, Alberta | Frigidaire | CFEB786JGS | F1 & F3 | The oven starts beeping code F3 or F1 after cooking about 30 minutes. Can you please advise if you have reconditioned timer available? | Repaired |
Southside Boularderie, Nova Scotia | Frigidaire | CGEB27S7C/S1 | N/A | RETURNED FOR WARRANTY WORK
• Light no longer works from touch pad (did before refurb.)
• Convection fan does not work (did before refurb.)
• Convection element does not work (same as before refurb.)
• Power supply (220) normal
• Power to timer P.C.B. normal
• Broiler - timer normal
• Bake - timer normal (did NOT work before refurb.)
• Door lock - timer normal
• Light works when door opens
• Wiring harness normal
• All connections normal (above confirmed by Cordell Brown Refrigeration & Major Appliance Parts & Service Ltd. 902-794-4096 as I believed that there must now be something else wrong after having the P.C.B. refurbished, particularly with parts that were working prior to and now not working). Please believe me that I am sending it back to you as I seek to uphold your good name and not slag it through any mud. So thank you for taking back for a second look.
Blessings,
Jason | Beyond Repair |
Delhi, Ontario | Frigidaire | cgeb27s7cb | f3 | f3 error, oven will not start up, heat up, if you can not fix this timer we will take a new or rebuilt timer from your inventory.
Frididaire SN: nf62722721
Clark Chernak
Tel: 519-512-2005 | Awaiting receipt of timer |
Middle Sackville, Nova Scotia | Frigidaire | CGEB27S7AS1 | F1 AND F3 | At first only one code mainly would show I think F1. I changed out the high limit and it seemed to be good for awhile. Then F1 and F3 started appearing and wont reset. | Awaiting receipt of timer |
Ottawa, Ontario | Frigidaire | CGEB27S7CS1 | F1 | Set oven to bake at 400F. Element turns on, then
temperature reading starts going up very fast,
reaches 400F while oven is still cold.
Temperature sensor seems to be working, reads
1kOhm at room temperature. | Timer inspected, no repairs necessary |
Trois-Rivièeres, Quebec | Frigidaire | CGEB27S7CS1 | none | The bake element is good (tested by a technician) but do not heat anymore. The broil element is heating. | Awaiting receipt of timer |
Québec, Quebec | Frigidaire | cpeb30s8cc2 | none | not getting any heat from bottom. broil is good, thermostat also. | Repaired |
Ottawa, Ontario | Frigidaire | CGEB27S7CS1 | F1 | Set oven to bake at 400F. Element turns on, then temperature reading starts going up very fast, reaches 400F while oven is still cold.
Temperature sensor seems to be working, reads 1kOhm at room temperature. | Awaiting receipt of timer |
Vancouver, British Columbia | Frigidaire | CGEB27S7C5 | N/A | Broil works no bake | Repaired |
St. John's, Newfoundland and Labrador | Frigidaire | CGEB27S7CS1 | none | display and all operation is dead. Signs of arcing inside display circuit board halfs. | Awaiting receipt of timer |
Ancaster, Ontario | Electrolux | CGEB27S7CB1 | None | Bake element will not energize. | Repaired |
Ancaster, Ontario | Electrolux | CGEB27S7CB1 | None | Bake element will not energize. | Repaired |
Salmon Arm, British Columbia | Frigidaire | CGEB27S7AS1 | F1 AND F3 | WORKS FINE FOR A SHORT TIME THEN STARTS BEEPING WHEN ERROR CODES F1 OR F3 COME UP. iF WE TURN POWER OFF THEN ON AGAIN IT WILL DO SAME AGAIN BUT FOR A DIFFERENT AMOUNT OF TIME BEFORE ERROR CODES. | Repaired |
Perth, Ontario | Frigidaire | CGEB27S7CB2 | N/A | Bottom element not heating up | Repaired |
Harrow, Ontario | Frigidaire | CGE B27S7CB1 | 3 | Set at 350 degrees oven continued to increase in temperature to mor than 500 and then set up a loud noise. When rebooted, it did the same. | Repaired |
Toronto, Ontario | Frigidaire | CPEB30S8CC2 | None | The lower heating element (Bake heating element) not working. All other parts including the fan and top heating element are working. | Repaired |
Durham, Ontario | Frigidaire | CGEB27S7CS1 | Error Code 3 I belie | Overheating/no temp control. I have already replaced the temp probe. | Repaired |
Keswick, Ontario | Frigidaire | CGEB27S7CB1 | none | no heating, checked temp prope over 1 k ohm, temp thermal breaker reset, both elements good, and door lock switch ok. board moduals making noise but releases after start on shows on screen. It started failing with one element failing and now after a few months both elements do not heat up. | Repaired |
Laval, Quebec | Frigidaire | CGEB27S7CS1 | N/A | No heat | Awaiting receipt of timer |
Pictou, Nova Scotia | Frigidaire | CGEB27S7CS1 | unknown | The oven reaches a certain temperature on bake (280) and goes no higher. Broil works. | Repaired |
Seguin, Ontario | Frigidaire | CGEB30S8AS1 | N/A | bake element does not work | Repaired |
Coquitlam, British Columbia | Frigidaire | CPEB30S8CC2 | Top heating element | Top heating element not working; top heating element was newly replaced. | Awaiting receipt of timer |
Salmon Arm, British Columbia | Frigidaire | CGEB27S7AS1 | F1 AND F3 | Starts and works great for a short time then goes off and shows F1 or F3 error code. If the power is cycled it will do the same but possibly for a different amount of time before same error. | Repaired |
Sherwood park, Alberta | Frigidaire | Cgeb30s8cs1 | N/A | Repair tech advise part failed | Awaiting receipt of timer |
Humboldt, Saskatchewan | Frigidaire | CGEB27S7CB1 | none | Oven does not heat up on bake or broil setting | Awaiting receipt of timer |
Montreal, Quebec | Frigidaire | CPEB30S8CC1 | Does not power on | Will not power on. Checked Double-line relays, seem OK. Took to an electronics repair shop. They spotter and repaired circuit trace burn due to apparent short, replaced burnt zener diode. Powered on and all LED segments lit up and stuck like that. Removed power and tried again, but it will no longer power up. Repair shop ordered and changed all IC's, but still won't power up. All original IC's are included separately in shipment. | Awaiting receipt of timer |
N.D. de HAM, Quebec | Frigidaire | CGEB27S7CS1 | f1, F3 and insists o | Just will not function | Timer inspected, no repairs necessary |
Surrey, British Columbia | Frigidaire | CGEB30S8CB1 | none | Broil element stopped working one year ago; but element tested fine. Bake element stopped working a week ago; but element tested OK. | Repaired |
fort mcmurray, Alberta | Frigidaire | CFEB389WE7 | no codes | Bake relay function 95% of time not working display slightly dim. | Repaired |
Calgary, Alberta | Frigidaire | CPEB30S8CC2 | No code | Oven won't heat, the on light comes on and i hear a clicking, it may be contacts making and breaking. The broiler works. I switched the element wires on the timer so the bottom element would come on instead of the broiler, but then it went to lock mode and wouldn't reset. I hope i didn't damage it further.
Please let me know fixed or not fixed. | Repaired |
Caledon Village, Ontario | Frigidaire | CGEB 27S7CS1 | n/a | need another timer this is not repairable | Awaiting receipt of timer |
ST-ANSELME, Quebec | Frigidaire | CGEB27S7CS | F1 | FI ERROR CODE OCCASIONNALY | Awaiting receipt of timer |
laval, Quebec | Frigidaire | cgeb27s7cs1 | no code wont turn on | will not turn on | Awaiting receipt of timer |
ST ANDREWS, New Brunswick | Frigidaire | CGEB27S7CB1318010701 | None | Bottom element not heating | Repaired |
MCNAB BRAESIDE, Ontario | Frigidaire | CGEB27S7CB2 | N/A | Oven stopped working - no display | Awaiting receipt of timer |
Sudbury, Ontario | Frigidaire | CGEB27S7CB1 | N/A | Broil works, Bake and convection d not. Element check ok. Power check ok | Awaiting receipt of timer |
Nanton, Alberta | Kenmore | C970-415-823 | F1 and F3 | The oven works good for awhile then either F-3 (most common) or F-1 code comes on. You can cancel and reprogram and sometimes the oven restarts and works fine and others it just produces the error code within a few seconds / minutes. | Repaired |
Minesing, Ontario | Frigidaire | CFEB389WEC8 | None | Oven will not heat up to set temperature. | Awaiting receipt of timer |
Redvers, Saskatchewan | Frigidaire | CPEB30S8CC2 | None | No codes come up. Everything was working until performed a self clean and now the bottom element will not heat up. Element test fine everything on the clock works just does not get bottom Elmer powerd up. | Awaiting receipt of timer |
Edmundston, New Brunswick | Frigidaire | CFEB389WEC8 | F3 | Oven doesn't work. When I push the COOK button, an F3 error code appears. | Repaired |
Sarnia, Ontario | Frigidaire | CGEB27S7AB1 | N/A | turns off..like power shut off | Repaired |
Armstrong BC, British Columbia | Frigidaire | CGEB27S7CB1 | N/A | BROIL WORKS SOMETIMES. BAKE AND CONVECTION DO NOT. OHMS ON ELEMENT READ 25. INITIAL TURN ON SENDS POWER, THEN RELAY FAILS? | Awaiting receipt of timer |
Swift Current, Saskatchewan | Frigidaire | cgeb27s7cs1 | unknown | Bottom element won`t heat. Element is ok. | Repaired |
Swift Current, Saskatchewan | Frigidaire | CGEB27S7Cs1 | none | Bottom element will not heat. Element is ok | Repaired |
Armstrong BC, British Columbia | Frigidaire | CGEB27S7CB1 | N/A | BROIL WORKS SOMETIMES. BAKE AND CONVECTION DO NOT. OHMS ON ELEMENT READ 25. INITIAL TURN ON SENDS POWER, THEN RELAY FAILS? | Awaiting receipt of timer |
Estevan, Saskatchewan | Frigidaire | CGEB27S7CS1 | NA | Bake will not work
Element tested okay | Repaired |
Laval, Quebec | Frigidaire | Cfeb30s8cc2 | F1 | conventional bake,bake,clean,and broil will not work | Awaiting receipt of timer |
Baie-Comeau, Quebec | Frigidaire | 100-755-02 | No heat | | Awaiting receipt of timer |
Victoria, British Columbia | Kenmore | C970-418826 | N/A | Oven Lamp always on with oven door open or closed. Convection Motor always on when door is closed.
Bake element never turns on.
Convection element turns on in all cycles.
Broil element turns on in all cycles.
Oven Lamp Relay always engaged, always measures 7.2VDC on relay coil connectors.
Convection Motor Relay always engaged, always measures 6.6VDC on relay coil connectors.
Measured | Repaired |
Coldstream, British Columbia | Frigidaire | CGEB30S8AS1 | N/A | No Broil. Relay in clock not closing. | Awaiting receipt of timer |
LIttle Harbour, Nova Scotia | Frigidaire | CGEB27S7CB1 | No code, no power | Stove was fully operational , baking cookies then nothing, complete power failure | Beyond Repair |
Hunter River, Prince Edward Island | Frigidaire | cgeb27s7ab1 | n/a | panel to turn wall oven on/off, set temp etc. seems to have stopped working to the point where if I do get it to turn on I have to shut off the breaker in fuse panel to turn off oven. | Timer inspected, no repairs necessary |
Gatineau, Quebec | Frigidaire | | N/A | Bake element doesn't work. | Awaiting receipt of timer |
Ajax, Ontario | Frigidaire | CGEB27S7CB1 | F1 | On start up of bake or broil F1 code is given. There appears to be damage(de-soldering) to the underside of the control board at the bake and broil relays. | Repaired |
Newmarket, Ontario | Frigidaire | CPEB30S8CC2 | N/A | Bake will not heat up, tested element 18 ohms, no broken wires found. | Awaiting receipt of timer |
Moorefield, Ontario | Frigidaire | cgeb27s7cb1 | N/A | no power to elements suspect relay in control | Repaired |
Surrey, British Columbia | Frigidaire | CGEB27S7CS1 | none | display does not light up.
Oven power is ok | Beyond Repair |
Cardigan, Prince Edward Island | Frigidaire | CGEB27S7CB1 | F1 | The F1 Code appears, there is no power to either the Broil or Bake option. The F1 code appears within the first 1-2 minutes. No Preheat action as well.Have checked several cold solder joints but to no avail. Unit may have been repaired or re-soldered previously. Customer has only owned this house for several years and the Wall Oven was there previously. | Repaired |
Winnipeg, Manitoba | Frigidaire | CGEB30S8AB1 | F1 | My oven will not heat above 350 degrees. The relays are clicking, but the heat is not rising past that.
I have purchased an EOC from you before. | Repaired |
Edmundston, New Brunswick | Frigidaire | Cfeb786jgb2 | F1. F3 | Having hard time to see the temperature on the display. Now when we put the timer on it gives the fault code and oven stop working. | Awaiting receipt of timer |
castlegar, British Columbia | Frigidaire | cgeb30s8as1 | f1 f3 | get f1 and f3 code after a few minutes . temp probe ok | Repaired |
Mississauga, Ontario | Frigidaire | CGEB30S8CB1 | did not see any | When I used the baking feature, I heard the click but baking element was cold to the touch and broiling element was glowing red and a little smoke came out. Smelled like burning wires. Opened it but nothing seem burned. Removed clock for repair. | Repaired |
Orillia, Ontario | Frigidaire | CGEB27S7CB1 | Just shows 100 F | Just shows 100 F and does not heat. | Repaired |
Calgary, Alberta | Frigidaire | CgEb30S8cB1 | N/A | ELECTRONIC CONTROL PANEL is not working
I can set the BAKE for 350, but the oven does not heat up
I had a service man out & he said this is what I need | Repaired |
Tottenham, Ontario | Frigidaire | CGEB27S7CB1 | F1 | Intermittent F1 failure code, however now appears to be premanent | Repaired |
Trenton, Ontario | Frigidaire | CGEB27S7CS1 | F1 | no display ,
oven doesn't work | Awaiting receipt of timer |
ST CATHARINES, Ontario | Frigidaire | CPEB30S8CC2 | NO FAILURE CODES | TOP ELEMENT NOT WORKING
BOTTOM ELEMENT NOT WORKING
CONVECTION BURNIER NOT HEATING
TIMER SHOWS TIME ETC BUT THATS IT | Repaired |
Trenton, Ontario | Frigidaire | CGEB27S7CS1 | F1 | no display ,
oven doesn't work | Awaiting receipt of timer |
Didsbury, Alberta | Frigidaire | cgeb30s8cs1 | N/A | Lower bake element stopped, replaced still not working.
Tested leads on control board no voltage out. | Repaired |
Terrebonne, Quebec | Frigidaire | CPEB30S8AC2 | N/A | The display heating not workink
Everyting is OK except that | Repaired |
Boucherville, Quebec | Frigidaire | | N/A | Relays blown up | Repaired |
Windsor, Nova Scotia | Frigidaire | CGEB27S7CB1 | None | Bake element won't heat up ,broil element works no codes | Awaiting receipt of timer |
Belleville, Ontario | Frigidaire | CGEB27S7CB1 | N/A | BROILER DOES NOT WORK
CONVECTION INTERMITTENT
TAKES TO LONG TO COOK ANYTHING | Repaired |
SAINT-LAMBERT, Quebec | Frigidaire | CPEB30S8CC1 | N/A | Lower element does not work on any setting such as Bake, Convection. The upper element works for all settings. The convection fan works and when the temperature is set for bake on convection it only shows 100 degrees. We replaced the original control panel five years ago after having the same problems. | Repaired |
Winnipeg, Manitoba | Frigidaire | CFEB786JGB3 | F1 AND F3 | AFTER IN BAKING MODE FOR A PERIOD TIME IT WILL START TO BEEP AND DISPLAY ERROR F1 OR F3. THE HEAT SENSOR WAS TESTED AND IT WAS CONFIRMED THAT IT WAS GOOD. THE ISSUE APPEARS TO BE THE CONTROL BOARD. | Repaired |
Toronto, Ontario | Frigidaire | CGEB30S8CB | N/A | The oven Bake cycle not working, no heat on the element, temperature will not go up. The Broil Cycle works, Clock works. | Repaired |
Richmond Hill, Ontario | Frigidaire | CPEB30S8CC2 | NONE | The bake element doesn't come on | Awaiting receipt of timer |
Varennes, Quebec | Electrolux | CGEB27S7CB1 | N/A | No error code. Oven won't heat. Control unit clicks. Elements are good. Display is alright too. | Repaired |
Montreal, Quebec | Frigidaire | | N/A | down gril of the oven is not working (top is all right) | Repaired |
Longueuil, Quebec | Frigidaire | CFEB389WEC8 | F1 and F3 | The oven works fine for a short period (usually 10-20 mins) and then will stop with a F1 or F3 error. In case of F3 the oven will not restart until it cools down. The temperature probe has already been replaced. | Repaired |
St. George, New Brunswick | Frigidaire | CGEB27S7CB2 | no heat | the bottom element is not heating | Repaired |
Chase, British Columbia | Frigidaire | CPEB30S8CC2 | N/A | bake element wont work. | Repaired |
Laval, Quebec | Frigidaire | Electrolux | F1 | We had our oven assessed by a technician who said it was the relay for the bottom element that was malfunctioning.
The element was also checked and there is no problem with it. | Repaired |
Kelowna, British Columbia | Frigidaire | | N/A | Repairman said that bake module does not work. When we turn on oven to bake - element does not heat up. He rewired it for the broil element and it did not work - so says the bake module needs replacement and recommended your firm. | Repaired |
Okotoks, Alberta | Kenmore | C970-418852 | N/A | Can't read the display very well, oven works but hard to read temperature and if on or off. | Awaiting receipt of timer |
Whiteshell, Manitoba | Frigidaire | CGEB30S8-CB1 | no lower element hea | lower element doesn't heat.
wall oven broil works fine.
lower element ohms out to 18 ohms, no visible issues.
Suspect relay: after turning on bake, one relay click after several seconds. After 5 seconds two more clicks in rapid succession. No heat.
with broil, one relay click and then heat | Repaired |
Kanata, Ontario | Frigidaire | CPEB30S8CC2 | None | Bake element no heat
Broil element no heat
Convection element no heat
Timer shows flashing clock
No failure code | Awaiting receipt of timer |
Kingston, New Brunswick | Frigidaire | Gallery Series / Frigidaire | None | Bake Element is Not working
Broil element works, and top element pulses on when on bake
Convection fan works
Both top and bottom elements test good with ohm meter
No voltage to bottom element wires | Repaired |
black diamond, Alberta | Frigidaire | CGEB27S7CB1 | N/A | I would like to have a reconditioned or new timer -- do you want the old timer sent to you?
Do you have reconditioned or new in stock ? If not what is the delivery time?
I will phone you Monday to discuss this with you to see what you recommend. Fred Cuthbert | Awaiting receipt of timer |
black diamond, Alberta | Frigidaire | CGEB27S7CB1 | N/A | I would like to have a reconditioned or new timer -- do you want the old timer sent to you?
Do you have reconditioned or new in stock ? If not what is the delivery time?
I will phone you Monday to discuss this with you to see what you recommend. Fred Cuthbert | Awaiting receipt of timer |
St-barnabe-sud, Quebec | Frigidaire | cpeb30s8cc2 | None | Clock button not working. Broil button not working. This timer was repaired about a year and a half ago for a different failure code. I do not recall the code at that time however. | Timer inspected, no repairs necessary |
Edmundston, New Brunswick | Frigidaire | CFEB786JGB2 | F3 and ones in a whi | I have a wall mount over( Frigidaire Gallery) . It seems to work ok but sometimes after 15-20 minutes we hear a beep and a fault code appears ( F-3 and sometimes it's F-1). We have to shut it down and restart. I've checked the temperature probe and it is in the range. We also noticed that the display is very dimmed. Was wandering if you think you could fixe it for me or if you would have one on hand. Thanks | Repaired |
Sharon, Ontario | Frigidaire | CGEB27S7AS1 | no | dead | Repaired |
bonnyville, Alberta | Frigidaire | CPEB30S8AC2 | N/A | bake and convection elements test ok, but do not heat. broiler element works ok | Awaiting receipt of timer |
Cardinal, Ontario | Frigidaire | CGEB27S7CS1 | N/A | When oven was turned on, upper element would heat, not fully but at least get warm. Lower element would not heat up at all. We bought a new lower element thinking it would correct the problem, it didn't. An electrician was here yesterday and tested both the older and newer element and said both were in good working order. He suggested it would be something with the panel. When turned on it would also do a lot of clicking but would never get past that sound or heat up. | Repaired |
ottawa, Ontario | Frigidaire | CGEB27S7CS1 | N/A | heat will not last indicates 350 internal not 350 | Repaired |
cranbrook, British Columbia | Frigidaire | CPEB30S8CC2 | N/A | DOESN'T HEAT UP | Repaired |
Kelowna, British Columbia | Frigidaire | ? Sticker is missing! | It just shut off com | Was in the middle of baking and then we just noticed the screen was black and the oven stopped working. The light in the oven did remain on though. | Beyond Repair |
plessisville, Quebec | Frigidaire | cpeb30s8cc2 | no code | lower element was not working , we did put a new one , some condition . | Repaired |
Maple Ridge, British Columbia | Frigidaire | CGEB30S8CS1 | N/A | control board failure, please let me know cost before completing transaction. Your website has no way to ask for a price that I can see. Thanks, Doug | Awaiting receipt of timer |
Sudbury, Ontario | Frigidaire | cgeb27s7cs1 | N/A | bake element is not working | Awaiting receipt of timer |
Vancouver, British Columbia | Frigidaire | CGEB27S7CB1 | No alarm code. | NO heat from bottom element. also in Convection mode the fan will run but no heat. Can measure resistance in the bottom element (after I removed it from the oven). Broil element does work. | Repaired |
Badger, Newfoundland and Labrador | Frigidaire | cgeb27f7cb1 | F1 & F3 | Broil does not work element not coming on F1 & beep
Oven heats to selected temp say 350f then goes off beeping f3 | Repaired |
RR1 Pain Court, Ontario | Electrolux | CGEB27S7CB1 | None | No output to the broil element. | Repaired |
Ancaster, Ontario | Frigidaire | cgeb27s7cs1 | No power on bake or | No power on bake or broil. | Repaired |
Candiac, Quebec | Frigidaire | Gallery | F3 | - Timer always displays F3 code. Temperature sensor was replaced but it did not solve the problem.
- Dimmed display | Repaired |
Calgary, Alberta | Frigidaire | CPEB30S8CC2 | N/A | Broil works, bake does not. Element continuity is OK. | Awaiting receipt of timer |
Sudbury, Ontario | Frigidaire | CGEB27S7CB1 | Not apparent | The display is showing all 8888 and some functions all lit up at same time... Like it is confused. | Beyond Repair |
vanderhoof, British Columbia | Frigidaire | cgeb27s7ab1 | just blank... no cod | I cliked on bake and everything diseapear... prob relay problem | Beyond Repair |
Blainville, Quebec | Frigidaire | CPEB30S8CC2 | none | no power at E7 | Repaired |
Ottawa, Ontario | Frigidaire | CFEB786JG | none | Dim display get dimmer as oven heats up. | Awaiting receipt of timer |
Windsor, Ontario | Frigidaire | CPEB30S8CC2 | none | -Digital display of temperature and operation mode is dim and very difficult to see.
-Convection and bake mode works intermittently.
-Clean mode does not work correctly. | Repaired |
Puslinch, Ontario | Frigidaire | CPEB 30S | Bake element will no | Electronic Oven Control, the bottom bake element will not heat up | Repaired |
St. George, New Brunswick | Frigidaire | CFEB786JGB3 | F1 & F3 | Shutting oven off, giving error signal.
Oven sensor tested good. | Repaired |
South Hazelton, British Columbia | Frigidaire | Gallery CFEB786JGS3 | F-1 | Oven fails to stay on. keep getting an f-1 code | Awaiting receipt of timer |
Three Hills, Alberta | Electrolux | MEM A 086 | N/A | First the broiler quit - element continuity tested OK
Then the main element quit - element continuity tests OK
I tested both where they plug on to the elements and was expecting 220V but got nothing | Replaced with reconditioned timer |
LETHBRIDGE, Alberta | Electrolux | CGEB27S7CS1 | N/A | AS PER OUR PHONE CALL | Replaced with reconditioned timer |
Temperance Vale, New Brunswick | Kenmore | C970-415822 | F1, F3 | Codes F1 andF3 come on and with many attempts , so far have been able to get to reset so the oven could be used. | Replaced with reconditioned timer |
Carrot Creek, Alberta | Frigidaire | CPEB30S8CC2 | None | No power to elements everything else checks ok except relay. Top element went first. Bake only heated to 120. Now no power to elements at all. Thank you for the insight on the relay.
I live in the country so please ship it Canada post.
Thanks Gene | Replaced with reconditioned timer |
Howick, Quebec | Frigidaire | CGEB27S7CS | N/A | Bottom element won't heat element tested okay by technician advised us circuit board was defective | Replaced with reconditioned timer |
Oakbank, Manitoba | Frigidaire | CGEB27S7CB1 | N/A | ELEMENTS ARE OK BUT DON'T FUNCTION CORRECTLY. They don't turn on. | Awaiting receipt of timer |
Québec, Quebec | Electrolux | CGEB2757CB1 | 8888 | The display is showing all 8888 and the oven no longer function (could not be started) | Replaced with reconditioned timer |
Val Gagné, Ontario | Frigidaire | CGEB27S7CS1 | Had electrician chec | Bake relay is faulty. Need new control board as relay is saudered in. | Repaired |
Keene, Ontario | Frigidaire | CGEB27S7CB1 | N/A | Bottom element/Bake function does not work | Repaired |
Aylesbury, Saskatchewan | Electrolux | Cgeb27s7cs1 | No code | Burn marks on board and board does not send power out to element when on bake bake. | Awaiting receipt of timer |
Sarnia, Ontario | Electrolux | CGEB2757S7CS1 | NA | Both elements will not heat, The oven temperature probe tests at 1080 OHMS, There are no charred wires. The display works and clock and light work. All the connectors appear in good shape | Repaired |
BEETON, Ontario | Frigidaire | CGEB27S7CB1 | F1 | Oven gave F1 error which i cleared by Cancel button. This repeated twice more before display went out and now no function | Beyond Repair |
Brampton, Ontario | Frigidaire | CPEB30S8CC2 | N/A | Convection and Baking Functions not working, but Broil works fine. | Repaired |
Toronto, Ontario | Frigidaire | CGEB27S7CB1 | none | The bake element doesn't turn on, but it has connectivity when tested. | Repaired |
ST. BASILE-LE-GRAND, Quebec | Frigidaire | CGEB27S7CB1 | F1 | After selecting BAKE or CONV or BROIL, heat will start but will soon (1-2 mins.) stop and display an F1 code. By restarting continuously until the oven temperature gets to more or less 200 degrees, the timer will then start working properly for any selection. Even after cancelling the selection or leaving the appliance unused for some time, it will restart easily as long as the internal temperature of the oven is averaging 200 degrees. | Awaiting receipt of timer |
Willow Beach, Ontario | Frigidaire | CGEB27S7CS1 | N/A | NO HEAT, BOTTOM ELEMENT. BROIL OK. LED DISPLAY SEGMENTS ARE DIMMED ON EVERY OTHER LINE HORIZONTALLY. | Awaiting receipt of timer |
Mississauga, Ontario | Frigidaire | CFEB786JGB3 | N/A | 1) Dim Display
2) Difficulty operating touch screen buttons | Awaiting receipt of timer |
Roseneath, Ontario | Frigidaire | CGEB27S7CB1 | N/A | wife was cooking dinner at 350 degrees and after a while display went blank and she noticed element was on and very hot. Unable to turn it off from control panel so isolated breaker at electrical panel | Beyond Repair |
Guelph, Ontario | Electrolux | CGEB27S7CB1 | None | Broil not functioning. Continuity on the element is okay.
Bake and convection are working so I am guessing the main relay is okay. | Awaiting receipt of timer |
Roseneath, Ontario | Frigidaire | CGEB27S7CB1 | display completely b | while cooking at 350 the display went completely blank but the upper element was on a very hot. unable to turn it off so went and turned of breaker at electrical panel. | Beyond Repair |
Val Caron, Ontario | Frigidaire | CGEB27S7CS1 | None | My Wall oven will not get up to temperature. The Broil element works. The Bake element does not work at all will not get hot. The element is good I checked the OHMs. It basicly stays at 100 F and doesn't move at all. I read a few reviews and some people had the same problem. If you need any more information please contact me. | Repaired |
London, Ontario | Frigidaire | CFEB386JGB2 | N/A | low display brightness; intermittently shuts off | Repaired |
Castlegar, British Columbia | Frigidaire | CGEB30S8CB1 | none | Oven Bake element does not heat up.
Measured 123Volts to one terminal | Repaired |
Castlegar, British Columbia | Frigidaire | CGEB30S8CB1 | none | Bake Oven Element only receives 123 volts | Repaired |
Hartington, Ontario | Frigidaire | CFEB786JGB | none | Panel LEDs have faded and are unreadable.
Please return ship by Canada Post | Repaired |
Chelmsford, Ontario | Frigidaire | cgeb27s7cb1 | N/A | Bottom element will not turn on. Oven doesn't heat up. Constant clicking sound from control panel. Bottom element was changed.
Note this is the second oven we have had (identical) and had the same problem with the first one. Timer went twice, apparently my luck is not getting bettter. | Awaiting receipt of timer |
Caledon East, Ontario | Frigidaire | CGEB27S7CS1 | N/A | Oven bottom element will not heat. broiler does work | Awaiting receipt of timer |
Pont-Rouge, Quebec | Frigidaire | CFEB386JGB2 | N/A | I am no able to control the oven and the display seem to be dead. Before the complete failure the display was very dim. There is no apparent defective part on the control board. | Repaired |
Kensington, Prince Edward Island | Frigidaire | CPEB30S8CC2 | N/A | oven will turn on but will not heat up | Repaired |
Lantz, Nova Scotia | Frigidaire | CGEB27S7CB1 | N/A | oven heats up to about 240deg but will not go any higher. No errors are shown on the clock. Lower element 1053ohms tests ok. Broiler element glows red. temp probe tests ok. Assuming clock timer is the issue. | Repaired |
Toronto, Ontario | Frigidaire | CGEB27S7CB1 | None | No error code. Timer seems to be functioning fine but elements do not turn on. | Awaiting receipt of timer |
Duncan, British Columbia | Frigidaire | CGEB30S8CB1 | Oven temperature ver | The oven operates normally. The temperature display has become extremely dim and difficult to read. | Repaired |
Montreal, Quebec | Frigidaire | Cgeb27s7cb1 | N/A | Clock works but not the heat. A technician told me it was a short circuit | Repaired |
Calgary, Alberta | Frigidaire | CGEB27S7CS | none | Broiler not working. Broiler element okay.
Display is dim and temperature settings hard to read | Repaired |
St-Colomban, Quebec | Frigidaire | CGEB27S7CB | N/A | Broil element heats and stops.
CALL ME OR SEND ME AN E-MAIL FOR PRICES
Thx | Awaiting receipt of timer |
St Adolphe d'Howard, Quebec | Frigidaire | cpeb30s8cc2 | f1 | f1 code
keep beeping till shut down breaker | Awaiting receipt of timer |
Woodburn, Nova Scotia | Frigidaire | CGEB27S7CB1 | F1 | F1 code then took it to get repair, now there is no numbers, just hear click when trying to set oven temp.oven not heating. | Beyond Repair |
Laval, Quebec | Frigidaire | | N/a | Does not work at all | Awaiting receipt of timer |
Calgary, Alberta | Frigidaire | CFEB389WEC7 | None | Display is very dim and the oven light won't turn off | Repaired |
Cambridge, Ontario | Electrolux | CGEB30S8AB1 | None, Dim display | Dim display | Repaired |
Edmonton, Alberta | Frigidaire | CGEB30S8AB1 | N/A | the oven doesn't heat up past 100 degrees | Repaired |
Calgary, Alberta | Frigidaire | CGEB27S7AB1 | Code 1 | Oven will intermittently stop heating up and display code 1 on the display panel. I have reset the oven power and the problem returned the next day. It did display code 5 once, but I can say it has not overheated. It will kick off from heating up well before it hits 300 degrees F | Repaired |
West Kelowna, British Columbia | Frigidaire | cpeb30s8cc2 | N/A | The broiler does not heat up. Had a repair person in and verified that when broil is selected, there is power coming into the board, but none going up to the burner. Checked and the broiler burner is in tact and wires are in good shape. | Repaired |
Burnt River, Ontario | Frigidaire | CGEB30S8CB1 | N/A | Bottom element won’t turn on. Broiler works but Bake setting doesn’t warm oven. | Awaiting receipt of timer |
Port Moody, British Columbia | Frigidaire | cgeb30s8cb1 | N/A | Initially the broil element would not heat. Broil element tested OK at 19 ohms. A year later the bake element also fails to heat up and also tested OK. Note that I am opting for a reconditioned timer instead of repair due to the cost of shipping the timer to you. | Repaired |
Calgary, Alberta | Frigidaire | CGEB27S7AB1 | Code 1 | The oven has been kicking off during some warmup cycles. the oven will stop heating and display Code 1. I have been able to reset it with a power reset, but the failures are happening quite frequently now. | Repaired |
Calgary, Alberta | Frigidaire | CGEB27S7AB1 | Code 1 | The oven has been kicking off during some warmup cycles. the oven will stop heating and display Code 1. I have been able to reset it with a power reset, but the failures are happening quite frequently now. | Repaired |
Rouyn-Noranda, Quebec | Frigidaire | Cgeb27s7as1 | N/A | No lite on timer | Awaiting receipt of timer |
Port Moody, British Columbia | Frigidaire | cgeb30s8cb1 | N/A | Initially the broil element would not heat. The element tested OK as did the relay controlling it. A year later the bake element failed to heat. I tested all 3 relays mounted on the back plate beside the timer (I used a 9VDC source) and they operated as designed. | Repaired |
Vancouver, British Columbia | Frigidaire | CPEB30S8AC2 | F3 | F3 code appears when the oven starts to heat up. Initially everything is working, and about 10-15 mins into baking, the F3 code appears. The temperature sensor/probe was replaced but no difference. The resistance of the temperature probe was measured to be 1080 ohms at room temperature. We disconnected the connector at the timer and measured the resistance at the wiring harness to check the wiring.
We also switched off/on power at the circuit breaker and that did not change anything.
The problem is consistent. | Repaired |
digby, Nova Scotia | Frigidaire | c970-415852 | f1 | error f1 | Awaiting receipt of timer |
Metcalfe, Ontario | Frigidaire | CPEB308CC2 | nil | no heat in all 3 modes, limit switches etc check out ok | Awaiting receipt of timer |
Edmonton, Alberta | Frigidaire | Professional Series | n/a | Broil works but, other modes don't. Seems like the relay(s) as per my research. | Awaiting receipt of timer |
Medicine Hat, Alberta | Frigidaire | CPEB30S8CC2 | n/a | I have a wall oven and the bake element does not heat up to the set temp. The element was checked and it is fine. My research tells me that the main control panel is the problem. | Awaiting receipt of timer |
Medicine Hat, Alberta | Frigidaire | CPEB30S8CC2 | n/a | I have a wall oven and the bake element does not heat up to the set temp. The element was checked and it is fine. My research tells me that the main control panel is the problem. | Awaiting receipt of timer |
Medicine Hat, Alberta | Frigidaire | CPEB30S8CC2 | n/a | I have a wall oven and the bake element does not heat up to the set temp. The element was checked and it is fine. My research tells me that the main control panel is the problem. | Awaiting receipt of timer |
Medicine Hat, Alberta | Frigidaire | CPEB30S8CC2 | n/a | I have a wall oven and the bake element does not heat up to the set temp. The element was checked and it is fine. My research tells me that the main control panel is the problem. | Awaiting receipt of timer |
digby, Nova Scotia | Frigidaire | c970-415852 | fi | fi error beeps and oven light turns on | Awaiting receipt of timer |
Toronto, Ontario | Frigidaire | CFEB389WEC8 | N/A | it appears that the existing timer down button is being triggered. When bake is selected, the temperature starts at 350, then just counts down to 200 then - - - in a matter of seconds. | Awaiting receipt of timer |
Maple, Ontario | Electrolux | CGEB30S8CB1 | N/A | Please send me reconditioned timer module 318010701 for CGEB30S8CB1 model. | Awaiting receipt of timer |
Medicine Hat, Alberta | Frigidaire | CPEB30S8CC2 | n/a | I have a wall oven and the bake element does not heat up to the set temp. The element was checked and it is fine. My research tells me that the main control panel is the problem. | Awaiting receipt of timer |
Medicine Hat, Alberta | Frigidaire | CPEB30S8CC2 | n/a | I have a wall oven and the bake element does not heat up to the set temp. The element was checked and it is fine. My research tells me that the main control panel is the problem. | Awaiting receipt of timer |
Medicine Hat, Alberta | Frigidaire | CPEB30S8CC2 | n/a | I have a wall oven and the bake element does not heat up to the set temp. The element was checked and it is fine. My research tells me that the main control panel is the problem. | Awaiting receipt of timer |
Medicine Hat, Alberta | Frigidaire | CPEB30S8CC2 | n/a | I have a wall oven and the bake element does not heat up to the set temp. The element was checked and it is fine. My research tells me that the main control panel is the problem. | Awaiting receipt of timer |
Kapuskasing, Ontario | Frigidaire | CGEB27S7ASI | F1 | F1 code appeared after power failure, can not reset the buzz, the breaker needs to be shut off to stop teh buzz | Repaired |
smithville, Ontario | Frigidaire | cfeb786jgs2 | no digits | The display is totally black | Awaiting receipt of timer |
Vancouver, British Columbia | Electrolux | CFEB786JGB3 | n/a (displays nothin | The timer was probably damaged during a power surge when BC Hydro re-connected a downed power line. Since that evening, it has displayed nothing.
Note: in removing the timer I broke the white plastic clip in position J1. This may need replacement as well. | Repaired |
Toronto, Ontario | Frigidaire | CFEB30S8AC1 | N/A | Broiler is working but bottom element is not so oven takes a long time to reach desired temperature | Repaired |
Roxton Pond, Quebec | Frigidaire | cgeb27s7cs1 | N/A | | Awaiting receipt of timer |
Verdun, Quebec | Frigidaire | pleb30s8ac | N/A | Broil ok, not baking and the element is ok 20 Ohms | Repaired |
St. Catharines, Ontario | Frigidaire | CFEB389WEC8 | F3 | F1 and F3 failure codes. Oven Sensor is OK. | Repaired |
Grande Prairie, Alberta | Frigidaire | CGEB27S7CB2 | Blank | Nothing comes on screen when power running to timer | Beyond Repair |
Roxton Pond, Quebec | Frigidaire | cgeb27s7cs1 | N/A | noting | Beyond Repair |
Mira Road, Nova Scotia | Frigidaire | CGEB27S7CS1 | None | When bake is selected, the oven heats extremely slow. Broil works. No error codes.
Switched BA and BR wires for relays. Bottom element now works with Broil selected but bake still doesn't work when selected. | Repaired |
Kelowna, British Columbia | Frigidaire | CFEB786JGB1 | N/A | Bake Relay failure likely - would like to purchase relay
G8P-UA-006203 separately, but will opt for rebuilt Timer. Please offer as possible | Awaiting receipt of timer |
Kelowna, British Columbia | Frigidaire | CFEB786JGB1 | N/A | Bake Relay failure likely - would like to purchase relay
G8P-UA-006203 separately, but will opt for rebuilt Timer. Please offer as possible | Awaiting receipt of timer |
Edmonton, Alberta | Frigidaire | cpeb30s8cc2 | Didnt give us one | The bake element is dead.We had the element checked and apparently it is in good form. | Repaired |
Vernon, British Columbia | Frigidaire | CPEB30S8CC2 | NA | Bake Element no longer works but tested element and it is fine | Repaired |
Stittsville, Ontario | Frigidaire | CFEB789JGB2 Wall Oven | N/A | In convection mode neither element gets hot.
In bake mode the top (broil) element only gets hot but this takes too long to heat up the oven since bottom (bake) element not on.
Have checked element resistance and the 3 other relays on the panel, all OK. | Repaired |
Margaree Harbour, Nova Scotia | Frigidaire | CGEB27S7CB1 | N/A | No heat - oven stopped heating; clock & timer not working; no readout on faceplate | Beyond Repair |
Margaree Harbour, Nova Scotia | Frigidaire | CGEB27S7CB1 | N/A | Timer is/was presently in for repair at Chicoutimi depot. Unable to be repaired, and is being returned.
Now, checking if your parts dept. would have a re-conditioned/repaired timer available for purchase. | Awaiting receipt of timer |
SUTTON WEST, Ontario | Frigidaire | CFEB786JGB3 | F1 / F3 | Before oven can reach desired temperature it shuts down and flashes a F1 and or F3 code. | Repaired |
Hantsport, Nova Scotia | Frigidaire | CGEB27S7CB1 | n/a | Broil element is not receiving any electricity - will not heat at all. | Repaired |
Saint Lazare, Quebec | Frigidaire | CFEB786JGS3 | F1, F3 | Oven turns on OK but F1, F3 codes along with continuous beeping appear once it reaches operating temperature. Temperature sensor confirmed OK at 1088 ohms. A secondary issue is that the clock time cannot be changed manually so that timed bake can't be used. | Repaired |
st-jean sur richelieu, Quebec | Frigidaire | CGEB27S7CS1 | F1 intermittent | F1 code | Awaiting receipt of timer |
Glenside, Saskatchewan | Frigidaire | CGEB27S7CS1 | N/A | Bake and convection bake quit working. Broil option does work. Does not show any codes. Clock and timer work. | Repaired |
Edmonton, Alberta | Frigidaire | CFEB786JGS2 | Dim temp. read out. | Everything works except can't read the oven temp as it is too dim. Tried new caps and that did not work for me, so would like to try a new timer if you have one. | Awaiting receipt of timer |
Ottawa, Ontario | Frigidaire | cefb786jg | none | Dim temperature display fades out when oven is hot. | Repaired |
Thornhill, Ontario | Frigidaire | cfeb789wfc1 | F3 | on part number 318010701 there is an error code F3.
on part number 9760422 - it was repaired by you and the problem came back, i noticed that the main black relay is the problem as when i am pressing on the relay hard its starting to work again, when its not working there is no power in the stove at all. | Repaired |
Southside Boularderie, Nova Scotia | Frigidaire | CGEB27S7CS1 | none | • no power to lower element and to convection element
• temperature read-out is dim
• RJ4 (resistor?) is loose or broken in C1 position on m/b | Repaired |
Sainte-Catherine, QC, Quebec | Frigidaire | CGEB27S7CS1 | Have not seen a fail | I have a Frigidaire wall oven CGEB27S7CS1, color white. No code errors have shown up. Timer part number 318010701. I believe it is the problem to my heating situation. The oven does not heat higher than 160 fahrenheit.
I have followed several steps from the internet to verify pieces. So far everything is pointing towards the timer. The wires appear to be in great condition, all the elements have continuity with the ohm meter. I removed the BA terminal and tested it. I had no reading.
I have full power to my fonctions 110v/240v. I verified all the heating elements, they all have continuity.
Now the question is did I verify everything? The piece is taken out and ready to be shipped. | Repaired |
Ottawa, Ontario | Electrolux | CPEB30S8CC2 | No | Oven does not heat up, broil or bake or convention. I replaced thermal fuse and replace three relays beside timer display circuit board.
As well oven light does not work when pressed however oven light works when door is opened. | Awaiting receipt of timer |
Ottawa, Ontario | Electrolux | CPEB30S8CC2 | No | Oven does not heat up, broil or bake or convention. I replaced thermal fuse and replace three relays beside timer display circuit board.
As well oven light does not work when pressed however oven light works when door is opened. | Awaiting receipt of timer |
Ottawa, Ontario | Electrolux | CPEB30S8CC2 | No | Oven does not heat up, broil or bake or convention. I replaced thermal fuse and replace three relays beside timer display circuit board.
As well oven light does not work when pressed however oven light works when door is opened. | Awaiting receipt of timer |
grande pointe, Manitoba | Frigidaire | cgeb27s7cs1 | N/A | broiler not working. element ok. convection bake motor not working. no 120 v. from board side wire. | Repaired |
Altona, Manitoba | Frigidaire | CPEB30S8CC2 | F1 & F3 | Oven will display an F1 or F3 error and shut off. I had an appliance tech in to confirm it was the EOC. I have not take the EOC off to confirm the part number and am going off what i see on the internet. | Repaired |
LAC SUPERIEUR, Quebec | Frigidaire | CGEB27S7AB1 | none | 1. Bottom element (bake) not heating.
2. display LED light very dim | Awaiting receipt of timer |
SAULT Ste. MARIE, Ontario | Frigidaire | CPEB30S8CC2 | N/A | need new unit | Beyond Repair |
Vancouver, British Columbia | Frigidaire | CGEB27S7CS1 | F1 and F3 | Intermittent F3 code and then a F1 code displayed. Oven temperature probe tests out at 1080 ohms. Also, dim display. | Repaired |
Kingston, Ontario | Frigidaire | CGEB27S7AB1 | None | Display is dim. Some segments don't show. The problem gets worse as the oven heats. There is heat discolouration in the upper left of the glass over the display. My preference is to get a remanufactured unit so I can continue to use the oven until the new part is received. If not possible, I will send it to you. | Repaired |
fenelon falls, Ontario | Frigidaire | cgeb27s7cs1 | nil | bake not wroking | Repaired |
London, Ontario | Frigidaire | CGEB27S7CB2 | N/A | Dim display, stove disengages from broil after several seconds | Beyond Repair |
Oakville, Ontario | Frigidaire | CPEB30S8AC1 | F-3 | When oven is set to bake, it will work for 30-40 minutes and then F-3 code appears | Repaired |
St. John's, Newfoundland and Labrador | Frigidaire | Frigidaire Gallery wall oven | NA | No power on timer | Beyond Repair |
East Selkirk, Manitoba | Frigidaire | CGEB30S8CB1 | N/A | Broiler quit working. Approximately 6-8 months later the bake feature quit working. I have checked both upper and lower elements for continuity and both check out fine. | Repaired |
Bright, Ontario | Frigidaire | CPEB30S8CC2 | none | Lower bake element does not heat | Repaired |
Steinbach, Manitoba | Frigidaire | CEB30S8CB1 | N/A | Bottom Element does not work | Repaired |
St-Lambert, Quebec | Frigidaire | CGEB27S7AS1 | Doesn't power up | Bake relay arced on the circuit board; no power at all since then. | Beyond Repair |
Stoney Creek, Ontario | Frigidaire | CPEB30SAC2 | N/A | No heat from bottom element | Awaiting receipt of timer |
Montreal, Quebec | Frigidaire | CGEB27S7CB1 | F1 | error code F1 with bipping... | Timer inspected, no repairs necessary |
Atwood, Ontario | Frigidaire | CPEB30S80CC2 | None | Bottom element will not work, Broiler works and the fan still functions | Repaired |
Mount Brydges, Ontario | Frigidaire | CPEB30S8CC2 | N/A | no working only on broil | Repaired |
Mississauga, Ontario | Frigidaire | Wall Oven | None that I can see | Lower (bake) element does not heat up. Checked element and it is fine. Upper Grill element works ok. Oven model is CPEB30S8CC2 | Repaired |
coquitlam, British Columbia | Frigidaire | CGEB27S7CB1 | N/A | broiler not working
oven was working fine but now its not working either | Repaired |
Nelson, British Columbia | Frigidaire | CFEB786JGS2 | N/A | everything works except the temperature light has faded and you can no long see the temperature that well. | Repaired |
Mississauga, Ontario | Frigidaire | CPEB30S8AC1 | No code | Bake element doesn't heat but had it checked (nothing wrong with it). Broil element works. Display lights up and is programmable. | Repaired |
Nelson, British Columbia | Frigidaire | CFEB786JGS2 | N/A | everything works except the temperature light has faded and you can no long see the temperature that well. | Repaired |
Kamloops, British Columbia | Frigidaire | CGEB27S7CB1 | None- no power | Repair or replace:
During baking, heat element clicked on, then control board went blank. No power to control board. Tried shutting off breaker and resetting, no power showing on board at all. Only thing still working is the oven light. | Awaiting receipt of timer |
Port Hope, Ontario | Frigidaire | CPEB30S8CC2 | N/A | After problem-free use, oven would not preheat. Bottom element not functioning though top one and convection element were when tested by local technician. He diagnosed a Clock/Timer failure. Advised replacement but no replacement part available. Prefer to repair rather than scrap otherwise perfectly operable oven. | Awaiting receipt of timer |
Quispamsis, New Brunswick | Frigidaire | CPEB30S8CC2 | No Code. No display. | No display. No response.
Oven light works. | Beyond Repair |
Point La Nim, New Brunswick | Frigidaire | CGEB27S7C | ONLY 110 | ONLY 110 GOING TO ELEMENT | Awaiting receipt of timer |
Spruce Grove, Alberta | Frigidaire | CGEB27S7CB1 | N/A | Bake element is not heating up. I believe broil still works but didn't confirm before sending. I have replaced the bake element but the problem was not repaired. No code is being displayed. | Repaired |
Prince Albert, Saskatchewan | Frigidaire | N/A | N/A | NO DISPLAY. | Beyond Repair |
Burnaby, British Columbia | Frigidaire | CFEB789JGS2 | None | Display is Dim otherwise controller works fine. | Repaired |
High River, Alberta | Frigidaire | CPEB30S8CC2 | Don’t know. | I replaced the bake element and it still does not heat. Talked to Howard yesterday and he assumes it is the clock/timer/EOC. | Repaired |
Senneterre, Quebec | Frigidaire | CFEB786JGB2 | NONE | The display of time and temperature has faded in recent years. Now the temperature of the oven is no longer visible. The rest, still works well | Repaired |
Spirit River, Alberta | Frigidaire | CGEB27S7AS1 | None | Bottom heat coil does not come on but when I switched wires with top heat coil it come on. | Awaiting receipt of timer |
Edmonton, Alberta | Frigidaire | Gallery series | None | Bake and broil do not work. No continuity from L1 to BR or BA. External relays test ok.
Also the display has gotten very dim. | Repaired |
Ajax, Ontario | Frigidaire | | N/A | No bake or broil. Tech said board is done. | Awaiting receipt of timer |
Peterborough, Ontario | Frigidaire | CGEB30S8CS1 | ?? | Technician says the relay controlling the bake element is faulty. | Repaired |
Peterborough, Ontario | Frigidaire | CGEB30S8CS1 | ?? | Technician says the relay controlling the bake element is faulty. | Repaired |
Wolfville, Nova Scotia | Frigidaire | cgeb27s7 | none | No display readings at all | Beyond Repair |
Gatineau, Quebec | Frigidaire | CGEB27S7AB | N/A | hard to read temperature very dim | Beyond Repair |
St. Clememts, Ontario | Frigidaire | CFEB786JGS | N/A | LED displays for temperature and clock are both too dim too see. | Repaired |
Grand Falls, New Brunswick | Frigidaire | CGEB27S7AS1 | N/A | The broil relay had previously stuck in ON position. At the time I disconnected blue wire to broil and customer used it this way for about 6 monts. Now the bake element does't come ON | Repaired |
Saint Hubert, Quebec | Frigidaire | 27" Gallery Series | N/A | not heating properly bake element replaced already | Repaired |
Barrie, Ontario | Frigidaire | Cfeb786jgb2 | N/A | Screen is dim and no bake | Awaiting receipt of timer |
Calgary, Alberta | Electrolux | Frigidaire CPEB30S8CC2 | none | The oven will not heat up. Had a local repair tech take a look at it and he said it is the controller/timer. The elements checked out OK. | Repaired |
Saint-Adolphe-d'Howard, Quebec | Frigidaire | CFEB786JGS2 | None | Unit is working but display is dim. It is very hard to read the set temperature. The clock is easier to read but still dim compared to what it used to be. | Awaiting receipt of timer |
Moncton, New Brunswick | Frigidaire | CGEB27S7CB1 | F1? | Convection Oven started acting up December 2019, it would would heat up to preheat temperature, then lose heat. I could play with temperatures, off On nd sometimes get the oven to heat. As of last week, Convection would not heat.
LCD display has been fading for years.
Bake has not worked for ...years, because it became disconnected in back from element.
Broil is working as of last week | Repaired |
London, Ontario | Frigidaire | C970-418821 | none | dim display | Repaired |
Nauwigewauk, New Brunswick | Frigidaire | CGEB27S7CB! | none | bake element will not work | Repaired |
Picton, Ontario | Frigidaire | CPEB30S8AC1 | F3 | F3 code intermittent when heating oven. Sensor was checked and is working fine. | Repaired |
Iroquois Falls, Ontario | Electrolux | Frigidaire / Electrolux 27" wall oven | N/A | Only 52 volts to bake element.
Bake element would not heat to 350 degrees. Element is fine, running with full continuity 24.7 ohms.
I think the model is Frigidaire CGEB27S7CS1 Electric Walloven Timer | Repaired |
Glenside, Saskatchewan | Frigidaire | Cgeb27s7cs1 | None | Everything works but the convection is intermittent. Have to sometimes try many times and play around with other functions before it turns on Can hear a click when you push convection but temp display doesn’t turn on for heat control. | Awaiting receipt of timer |
St-Colomban, Quebec | Frigidaire | CGEB27S7CB1 | NONE | OVEN WORKS 1 ON 3 TIMES | Awaiting receipt of timer |
Langley, British Columbia | Frigidaire | CFEB786JGS3 | N/A | Clock display is fine but temperature display (red led) is badly dimmed and difficult to read. | Awaiting receipt of timer |
Pontypool, Ontario | Frigidaire | CGEB27S7CB1 | N/A | Broiler stopped working a few months ago
Bake element stopped working last week.
Elements have no bubbling etc
You can select bake but element will not heat up and temp gauge will not read higher than 100. | Repaired |
Kamloops, British Columbia | Frigidaire | CGEB27S7CB1 | No code visible | I was cooking at 400f, heard a pop and all the lights went onto the oven control panel and cooking stopped. | Beyond Repair |
Jacksonville, New Brunswick | Frigidaire | Gallery Series | No Code | No power going to main oven element. Broiler still works. Fan for convection still work. Display all still works. | Awaiting receipt of timer |
Dundas, Ontario | Electrolux | cgeb27s7cb2 | none | Oven will not heat up past 300C and it takes about an hour to get that hot. broiler is working. burner for oven is confirmed working. | Repaired |
BRAMPTON, Ontario | Frigidaire | CGEB27S7AB | F3 | Originally bake worked but broil didn't. I removed timer myself and tried to solder the dull element but it doesn't work now with a F3 code. I may have damaged the electronic ribbon in the process. | Awaiting receipt of timer |
Edmonton, Alberta | Frigidaire | CGEB30S8CB1 | NA | When we push "BAKE" the lower element has not heat. the upper element has heat. We replaced the lower element, still has not heat. | Repaired |
Edmonton, Alberta | Frigidaire | CGEB30S8CB1 | NA | WE WANT TO BUY THE CONTROL BOARD # 318010701 | Repaired |
Stony plain, Alberta | Frigidaire | CGEB27S7CB1 | N/A | No power at all | Awaiting receipt of timer |
beachville, Ontario | Electrolux | cpeb3058cc2 | f1 -f3 | shuts off and throws f1 & f3 in aprox. 30min | Repaired |
Vaudreuil-dorion, Quebec | Frigidaire | CGEB30S8AB1 | F1 | THIS OVEN CONTROL SEEMS TO HAVE MANY NAMES, OVEN CONTROL , OVEN TIMES WHICH ONE IS IT , IT HAS BEEN REPAIRED SO MANY TIME S LAST TIME IN SEND STATE SIDE, LASTED 2 WEEKS | Awaiting receipt of timer |
Vanier, Ontario | Frigidaire | CGEB27S7CB1 | N/A | Broiler does not come on. Electrics in oven all check OK. | Repaired |
Smiths Falls, Ontario | Frigidaire | CFEB386JGS3 | N/A | Broil -> Works perfectly
Bake -> Takes a long time to heat up, but once hot maintains temperature
Convection -> Does not heat up at all
I did some investigation:
In Bake mode: The broil relay works as expected. However during the bake part of the cycle, the bake relay is intermittent. Typical behaviour is that it does not close for the first 5-10 cycles, will then close intermittently (if it closes it says close for then entire cycle), then will start to close consistently and work fine until the bake cycle is cancelled.
In convection mode, neither the broil relay or bake relay ever close.
I observed the relays using a volt meter over the course of many bake and convection attempts, and the behaviour described above was consistent.
I also tested the resistance of both elements, and both were right on spec. | Repaired |
Surrey, British Columbia | Frigidaire | CPEB30S8CC2 | N/A | Wall oven bake and convection bake cycles do not work (oven only heat up to 100-105 temperatures.
Broil cycle does work.
Technician has ruled out all other possibilities, but the timer. Timer model is no longer being supplied by manufacturer. | Awaiting receipt of timer |
Grande Cache, Alberta | Frigidaire | CFEB389WEC2 | none | Display too dim | Repaired |
Cypress county, Alberta | Frigidaire | Eletrolux | N/A | oven doesnt heat to set temp. | Repaired |
Cypress county, Alberta | Frigidaire | Eletrolux | N/A | oven doesnt heat to set temp. | Repaired |
Ottawa, Ontario | Frigidaire | CGEB27S7CB1 | NOT SHOWING ANY CODE | BROIL FUNCTION STOPPED WORKING SEVERAL WEEKS AGO (ELEMENT IS GOOD) . BAKE AND CONVECTION BAKE FUNCTIONS QUIT RECENTLY. CAN HEAR RELAYS CLICKING HOWEVER NO HEAT AT THE ELEMENTS. | Repaired |
Humboldt, Saskatchewan | Electrolux | CGEB27S7CB2 | Na | Convection Bake and Bake do not heat up. Broil seems to work fine. While testing a relay in the oven, a short was made. There is now a burn spot on the timer board, and the convection fan and light are on all the time, even with oven turned off. | Repaired |
Laval, Quebec | Frigidaire | CGEB27S7CS1 | --- | 2 techniciens came and found the same problem: the bake relay element (K402) on the relay board is broken. Everything else (clock, timer, broil element, convection element and fan, and bake element,...OK)
They suggested to change the "relay kit": part #318112701, just in case. This part has not been changed yet, because they were not sure it should be. | Repaired |
Saint-Jean-sur-Richelieu, Quebec | Frigidaire | CGEB27S7CS1 | F3 | Memory faillure | Awaiting receipt of timer |
Brossard, Quebec | Frigidaire | CGEB27S7CB1 | N/A | Bake element does not heat while the broil element works. Service man checked and and identified the electronic board as being the problem. If possible, I would like to purchase either a new one or a reconditioned one. | Awaiting receipt of timer |
Bethany, Ontario | Sears | C970-415851 | Fe3 (?) not sure too | Clock and temp have faded to the point where we cannot read/see anything. | Repaired |
Guelph, Ontario | Frigidaire | CGEB27S7CB1 | None, “CLN STOP†| Failure started after excessive moisture in upper area due to vent coming dislodged. Display now constantly shows “CLN STOP” and no option (bake, broil, conv bake) will heat up the oven. It allows you to set bake temp of 350, then it goes to the initial 100 and nothing happens. Prior to the failure, at this point the oven would “click” once as the elements engaged, now that doesn’t happen. | Awaiting receipt of timer |
Toronto, Ontario | Frigidaire | gallery wall oven | no code. display is | the display is dark. I'm guessing that the circuit board needs repairing | Repaired |
Surrey, British Columbia | Frigidaire | CPEB30S8CC2 | N/A | Convection bake and bake feature not working on wall oven unit. Broil feature still working. | Repaired |
Edmonton, Alberta | Frigidaire | CPEB30S8AC1 | F1 and F3 | Oven heats to a point and then stops.
Or it doesn't start at all | Repaired |
Kitchener, Ontario | Electrolux | CGEB27S7CB1 | N/A | Everything functions but no heat on bake or broil. | Repaired |
Nakusp, British Columbia | Frigidaire | frigidaire in wall oven | no codes | I had switched out the temp sensor and wanted to make sure the elements were getting power. My prong slipped and touched the relay connection and transmitter or whatever it is, at the same time and blew the board. When I attemped to soldered a new one on and try it, the blower would come on before anything was pushed. And then when I punched in 350 it would start to work, the broiler would stay on and then the clock face would just turn off and nothing would show on it. but the broiler and fan would still be running.
Before the clock face went blank, it would show everything on the clock face as it should; present temp would show and rise, bake would be lit on the clock. Clock would show time of day and all this would happen for under 30 seconds and then nothing. Sure hope this helps call if you need any other info.
Thank you | Beyond Repair |
Winnipeg, Manitoba | Frigidaire | cgeb27s7cb1 | F3 + F1 | Several minutes after the oven reaches the pre-set temperature it generates the F3 error code and powers down with the F1 error code following some time after that. Temperature probe and connecter has been replaced but did not resolve the problem. | Repaired |
Calgary, Alberta | Frigidaire | CPEB30S8CC2 | None | Bake funtion kicks out mid way if oven opened | Awaiting receipt of timer |
Sault Ste.Marie, Ontario | Frigidaire | cfeb386jgs3 | N/A | the present board has blown segment on the power input | Awaiting receipt of timer |
Montreal, Quebec | Frigidaire | CPEB30S8CC1 | F3, F1 | LED display is always dim and timer produces F3 and occasional F1 errors, usually after the oven has been running for over 20 minutes. I have repaired the F3 - F1 issue several times over years by redoing a couple solder joints on the PCB where the relays are. The fix usually lasts for a number of months but the problem eventually re-occurs. | Repaired |
Kamloops, British Columbia | Frigidaire | CGEB27S7AB1 | No Failure Code | Bake element not receiving power from the board, everything else appears to unction normally. | Repaired |
Sherwood Park, Alberta | Frigidaire | CGEB27S7CB2 | None | Bake Element does not come on at all.
( No Codes Displayed ) | Repaired |
gaspé, Quebec | Frigidaire | cpeb30s8ac1 | N/A | the element no heat | Beyond Repair |
Ormstown, Quebec | Frigidaire | CGEB27S7CB2 | None | Oven will not come up to temperature. About 100 degrees less than indicated.
Local serviceman broke white multi pin lock. If you can’t repair I think I can secure it. | Repaired |
LANGLEY, British Columbia | Frigidaire | CGEB27S7AB1 | F1 & F3 | WORKS MOST OF THE TIME , WE DO NOT USE IT ALOT BUT WOULD LIKE IT TO WORK . IT WORKS TILL IT GETS HOT ,THEN SOMETIMES THE CODE F1 OR F3 WILL COME ON AND IT WILL STOP. THEN WE SHUT IT OFF , RESTART IT AND IT WILL START WORKING AGAIN TILL IT FINISHES
THERE IS A BURN SPOT ON THE LEFT UPPER CORNER OF THE FACE | Beyond Repair |
Candiac, Quebec | Frigidaire | Cfeb786jgb3 | F3 and F1 | F3 code appears periodically sometimes F1 prob ok tested | Awaiting receipt of timer |
Lethbridge, Alberta | Frigidaire | CGEB27S7CB1 | N/A | Bake function element not heating. Broil element works. | Repaired |
victoriaville, Quebec | Frigidaire | cfeb786jgb3 | f1, f3 | after 30 min. code f1 or f3 | Awaiting receipt of timer |
CANDIAC, Quebec | Frigidaire | CFEB786JGB3 | F3 AND F1 | RESISTANCE PROB OK | Awaiting receipt of timer |
Winnipeg, Manitoba | Frigidaire | CFEB386JGS3 | F1 and F3 | Wall over will work for 5 or ten minutes and then produce either an F1 or F3 error code.Temperature sensor prob has been replaced, yet the error codes persist. | Repaired |
Lanlgey, British Columbia | Frigidaire | cgeb30s8cb1 | N/A | oven does not heat up properly | Awaiting receipt of timer |
Calgary, Alberta | Frigidaire | CGEB27S7CB1 | N/a | Oven will not heat up. Have checked element and no issues; Broiler still works. | Repaired |
Anola, Manitoba | Frigidaire | CPEB30S8AC2 | None | Oven is slow, or will not get to temperature on bake or convection bake. This is intermittent, sometimes it will get to temp quickly, sometimes slowly, sometimes will not. Sometimes will get to temp but then drop temp. Past few months tapping the relay has worked when it would not get to temp but that is no longer the case. Broil works properly. | Awaiting receipt of timer |
Ancaster, Ontario | Frigidaire | | N/A | Not Power is E7 BA | Awaiting receipt of timer |
Calgary, Alberta | Frigidaire | CFEB386JGB2 | F1 | F1 ERROR AND BEEP - STEADY - NO OVEN CONTROL BUTTONS FUNCTION | Repaired |
Saint-Basile-Le-Grand, Quebec | Frigidaire | CGEB27S7CB1 | none. Does not heat | Top heating element has not been working for a few years. Bottom heating element stopped working a month ago. Local repair person said the problem was the timer (and he could not source a replacement with his business partners). After putting the oven back in place, the bottom element worked. It has not failed again. | Repaired |
Wickham, Quebec | Frigidaire | CGEB27S7CS2 | N/A | | Awaiting receipt of timer |
Listowel, Ontario | Frigidaire | CGEB27S7CB1 | N/A | Display does not come on | Beyond Repair |
Mont-Saint-Hilaire, Quebec | Frigidaire | CFEB786JGB3 | F1 F3 | Intermittent F1 and F3 error codes | Awaiting receipt of timer |
Ottawa, Ontario | Frigidaire | CGEB30S8AB1 | n/a | This is an intermittent problem. Over the past few days it has started to happen more frequently. The control board will completely turn itself off (no clock shown) and the oven burners also turn off, but the internal oven light still works. After some period of time it will usually turn itself back on but that may be 5 minutes or 5 hours.
I disconnected the power, took the cover off of the oven so that I could access the control board, and turned the power back on. The clock was NOT on. I put a multimeter on the Line and Neutral terminals (E2 and L1) for the transformer and measured 120V. The clock was still NOT on. I tapped/hit the control board with a probe a couple of times and it turned itself on. Measured the voltage again and was still 120V across E2/L1. | Repaired |
Nakusp, British Columbia | Frigidaire | CGEB27S7CB2 | No display | Was cooking and heard a pop, then the display of my oven turned off. I checked the circuit breaker and it was still on. The oven light still functions, just the display no longer lights up and I can no longer use the oven as a result. | Awaiting receipt of timer |
Ottawa, Ontario | Frigidaire | cfeb389wec7 | no display | no display on control panel | Repaired |
Gatineau, Quebec | Frigidaire | CGEB27S7AB1 | Does not respond to | The oven would shut off after a certain time so I replaced the electrolytic capacitors (6) on the 2 interconnecte circuit boards that make up the control module. After that, the module would not respond to switches on the control panel. I repaired the flat cable from the switches which had lost contact inside the connector (Crimpflex), 5 connections. Still, the display kept on flashing the time of day but no response from the switches. So now I suspect the control module. Maybe the proprietary Robert Shaw chip? | Repaired |
Sherwood Park, Alberta | Frigidaire | CFEB786JGB2 | F3 | Replaced temp probe, still gives F3 fault intermittently. | Repaired |
Fisherville, Ontario | Frigidaire | CGEB27S7CS2 | n/a | the clock is on, it will accept commands but nothing works. I had my local appliance repair person check over the oven and he said this was the problem
BTW do your longer warranties include shipping? | Repaired |
Sherwood Park, Alberta | Frigidaire | Cfeb786jgs2 | F1-f3 | Beeps f1_f3 codes temp light only shows 1/2 screen | Repaired |
montreal, Quebec | Frigidaire | CGEB30S8CS1 | n/a | All off - electricity arrives at Control board (timer) but oven gives zero sign of life... | Awaiting receipt of timer |
Sussex, New Brunswick | Frigidaire | CGEB27S7AS1 | none | Display is dim. Do you have a replacement either new or used? | Awaiting receipt of timer |
Calgary, Alberta | Frigidaire | CPEB30S8CC2 | none | No work of heating all.
convection fen was work. | Awaiting receipt of timer |
Halifax, Nova Scotia | Frigidaire | CFEB386JGB2 | bake element not com | Bake element will not come on, had it diagnosed and they told me the part was no longer available. did it was the clock timer a relay was not working. Also we noticed over the last year the clock is not as bright and flickers from time to time. | Repaired |
Calgary, Alberta | Frigidaire | CPEB30S8CC2 | none | No work of heating all.
convection fen was work. | Awaiting receipt of timer |
Halifax, Nova Scotia | Frigidaire | CFEB386JGB2 | BAKE ELEMENT NOT WOR | BAKE ELEMENT WAS TESTED BY A TEC HAS 120VOLTS ON ONEE SIDE NOT 240 VOLTS | Repaired |
Greely, Ontario | Frigidaire | cfeb389wec7 | no display | Note: I had this control panel repaired because of no display however when I tried it, oven and broiler would not turn on. I have a backup panel which is very dim, however, oven and broiler work with that panel. | Awaiting receipt of timer |
Spruce Grove, Alberta | Frigidaire | CPEB30S8cc2 | no code | the timer face is blank | Repaired |
Regina, Saskatchewan | Frigidaire | CGEB27S7CB2 | N/A | Oven won't reach set temperature. Element heats up and then shuts off. | Repaired |
Greely, Ontario | Frigidaire | cfeb389wec7 | no display | Note: I had this control panel repaired because of no display however when I tried it, oven and broiler would not turn on. I have a backup panel which is very dim, however, oven and broiler work with that panel. - REPAIR UNDER WARRANTY | Awaiting receipt of timer |
Salaberry-de-Valleyfield, Quebec | Frigidaire | CGEB27S7CB1 | F1 | Problem started as oven was functionning for over 1 hour. It stopped heating and start locking the door. Cancel button wouldn't do anything. I shut off the breakers and when I restarted the oven, it worked for 5 minutes and now code F-1 appears with intermittent alarm on and off. | Awaiting receipt of timer |
Greely, Ontario | Frigidaire | cfeb389wec7 | no display | Note: I had this control panel repaired because of no display however when I tried it, oven and broiler would not turn on. I have a backup panel which is very dim, however, oven and broiler work with that panel. | Awaiting receipt of timer |