Jenn-Air Gas/Electric Slide In Range SVD48600P Timer Repair

I have a Jenn-Air oven, model # : SVD48600P. My wife was heating up the oven, she said it got "super hot" and came up with an "F2" error message and started beeping. She couldn't get the beeping to stop after repeatedly hitting the cancel button, finally she unplugged the oven and everything came to a halt. The oven was installed in 1999 and haven't had any problems until now. I found the error / fault codes and found 2 different repairs. First F2 code repair is : Oven too hot - Replace relay board (if present) or oven temperature sensor. Second F2 was for "Newer Style" oven range : Oven temp sensed; over 600F sensed by control in time of day mode, bake mode, or over 900F sensed in clean mode, Repair - Ohm test the oven temperature sensor, if ok, change power relay board. I've found the sensor in the oven(Ihaven't removed it yet oven still a little warm) and I have a meter, I am a DIY'er. Any all suggestions welcome, hope I gave enough info. thanks, XXXXX XXXXX

I have a jenn- air svd48600 series combination gas-electric grill-oven and oven, purchased in 1996. Display does not come on, oven cooling fan runs nearly all the time when oven is in use. Time to buy a new one, or is this good for a repair? Thanks for your help, Sue

I have a jenn-air svd48600p gas-electric grill-oven with convection oven and a f3 code any ideas how to clear it?

My Jenn-AIR SVD48600p electric oven stopped working. The front control panel that controls the oven is dark. The cook top gas burners, exhaust fan and oven light work. Circuit breakder has not tripped.

i have a jenn-air range, model svd48600p, the oven door stays open about a good 2-3 inches when looking at it from the side. i have replaced the hinges on it already no difference. i have checked the level & squareness of the outter frame, it seems fine, no obvious damage. i don't see any adjustment slots on the hinges or the mounting supports for the hinges on the frame. any suggestions would be helpful.

Fault Code F2 Jenn-Air Oven Model # XXXXXXXXX

WE HAVE A JENN AIR OVEN MODEL #SVD48600P THE HEATING ELEMENT BLEW AND HAS BEEN REPLACED BUT NOW THE CONTROL PANEL ISN'T WORKING. RELAY HAS BEEN REPLACED AS WELL. wHAT NEXT?

I have a Jenn-air 30" gas range model #SVD48600P. The door doesn't close the last 3/4". I ordered new hinges and replaced them. It seems there is not enough tension. Any ideas.

Hi, my Jenn Air slide in Electric Kitchen oven model # SVD48600P needs the Relay Board part # 71002144 replaced and this part number is no longer available. How do I find this part?

Jenn-air SVD48600P oven will not work / F3 error . I recently replace the expense control / clock unit on my oven because it would not heat. This was advice from repair person. Once replaced the over worked again, for about 10 minutes, and now there is an F3 error flashing and the internal fan will start running for absolutely no reason. With only 4 days until Christmas dinner, I'm running out of time...

Hi. I have a Y-2K Jenn-Air Electric Oven, with a gas cooktop. Model#SVD48600. The other day we finally got the clean mode to work-- didn't realize we had to push the oven door for the lock to engage. After the cleaning was completed, the F2 error light came on. The fan kept running, and the lock would not disengage. Eventually the lock disengaged, and the fan shut off. However, the next morning the fan spontaneously came back on, and stayed on until yesterday, mid afternoon. This morning, the fan spontaneously came back on, and the F2 error came up again. In spite of repeated attempts to click the cancel/off button, the F2 would repeatedly come back on. I eventually unplugged the plug from the power supply, and am now ready to "dig in" to see what I need to fix it. According to the schematic, the F2 error is an Ohm Sensor. If the resistances do not match, I should either replace the sensor, or the whole relay board. Your helps would be appreciated in my troubleshooting. 1- I am not an

Try here for the manual Download SVD48600.pdf

I have a Jenn-Air Electric oven that the oven elements wont work. I replaced the oven sensor today and it did have some heat damage on the wiring adaptor. However, there is no change. I have tried bake, broil and clean and none work. Sometimes it will flash a F5 code but not always. Most times, it will show that "preheat" is on but never heat up. I have inspected the upper and lower heating elements but found nothing obvious. Everything else works fine.

Original problem...oven cooling fan running by itself and when Bake or Broil selected....doesn't work....did tests with Stop Key....now F3 displays....it says that ohm sensor should be checked...not sure what part that they are talking about I have replaced clock ( main circuit board) but to no avail...

My clock works but it does not beep anymore when time has expired. Any idea what the problem may be or what part I need to order?

My Jenn-Air range is having problems with the control panel. The only button that doesn't work is the up arrow. The rest of the control panel works fine. I am assuming that this was the first button to go since I use the up arrow the most. Does the whole control panel need to be replaced, or is there something that can be done to fix the up arrow? I cannot use the clock and can only bake up to 350 degrees w/out the up arrow. I would really like to avoid having to pay around $400 for a new control panel and the labor to repair it.

Both upper and lower oven elements won't heat beyond warm (100 degrees)Jenn-Air Model# SVD48600P

my oven isn't getting warm...what to do, everything else seems to be working.model # SVD48600P

element burn out bottom jennair range element burn out bottom range jennair SVD48600p repain man replaced element and main board with clock range still would not work but he did not know what else could be problem

I can't lock the oven door to perform self cleaning. I there a handle to manually lock door? or is there just a problem with the door latch assembly