WB27K5055 General Electric (GE)/Kenmore Range (Stove, Oven) Timer

Failure codes, problems, and resolutions for General Electric (GE)/Kenmore timer model # WB27K5055

General Electric (GE) ERCs and General Electric (GE) stove clocks and timersKenmore ERCs and Kenmore stove clocks and timers Manufacturer :  General Electric (GE)/Kenmore
Part Number :  WB27K5055
Appliance Type :  Range (Stove, Oven)
Color : 
Description :  Cl/Oven Controller - Discontinued by the manufacturer

 
 
Do you have a failed General Electric (GE)/Kenmore WB27K5055 timer?
Click here:

We can repair or replace your faulty WB27K5055 timer.
Request Appliance Timer Service

Recent Service Requests


CityManufacturerModel NumberPart NumberFailure CodeProblem DescriptionResolution
benton, ArkansasGEWB27K5055N/Aoven only works on max temperature. any setting lower than that, it warms up for one to two minutes and shuts off and reads the set temperature, not the actual temperature.Beyond Repair
South Mills, North CarolinaGEWB27K5055N/AOven does not reach set temperature.Repaired
huntsville, AlabamaKenmore911.4012190wb27k5055no codeOven will not warm to selected temp. You can set oven for 350 and it will beep like it is up to temp after only a minute or so. You can sed oven for 350 and even after 45 min oven will only heat up to around 100 degrees. Heat probe seems to have checked out and seems to be working as it should.Repaired
Ashland, MassachusettsKenmore911.4712991WB27K5055F1F1 on occassion. When I turn on Bake unit shuts off, with no error withing 10 seconds.
If I start broil and switch to back then the unit works till I shut it off. When I shut it off I then get the F1 error code.
Beyond Repair
Mechanicsville, VirginiaGeneral ElectricJDC27GOP2BGWB27K5055NONEPut the range in broil and it works fine. Set it to bake and in about 4 seconds it beeps(instead of 'clicking on') and the 'on' light comes on. When checking current at the bake element I get 120v on the orange wire and 0 on the yellow wire. No codes given.Repaired
Brighton, TennesseeGeneral ElectricJDC27GOP1BGWB27K5055F1If the timer is beyond repair, then I'd like to purchase one from inventory.

Symptoms: beeping, non-stop. Code F1 showing in display. Tried simple reset, then cut power to unit and finally took it apart and unplugged the ribbon cable to reset, with no luck.
Awaiting receipt of timer
Pelzer, South CarolinaGeneral ElectricJDC27GPWB27K5055F1When the stove is plugged in, it starts beeping and displaying an F1 fault on the screen. We hit the clear button but it keeps beeping. All of the components function, all eyes heat up and the oven also does, but it constantly beeps and displays the fault.Beyond Repair
ROCHESTER, New YorkGeneral ElectricJDS27GP3BGWB27K5055F-1F-1 COMES ON AND TONE KEEPS GOING OFF AND WILL NOT RESET.Beyond Repair
Hebron, MarylandKenmore9114012190WB27K5055noneReading sensor input as 160F @ room temp. - sensor resistance checks out @ 1089 ohms.
It has now stopped operating the elements (both) since our phone conversation Mon, 10/31 AM.

****PLEASE NOTE: Per our conversation, I understand you should be getting one of these returned shortly from another customer who just purchased an in-stock one. I would like to purchase that one, when rebuilt, if mine is beyond repair. Thank you.
Repaired
Mena, ArkansasKenmore911.4012990WB27K5055F-1Oven works fine but it Beeps constantly and displays a F-1 message when oven is not in use.Repaired
Harvest, AlabamaGeneral ElectricJDC27GOP1BGWB27K5055noneController is 20 years old and it takes forever for the oven to heat up. I have to set the temp. 100 degrees higher on the controller than what is needed and then it takes about an hour for the oven to reach the temperature. Clearly a PID problem, but GE doesn't supply these controllers any longer. Trying to get the oven ready for the holidays. THANKS!Replaced with reconditioned timer
Chesapeake, VirginiaKenmore911.4012190WB27K5055No failure code give-Doesn't reach desired temperature (ex. must set to 500 to get 350).
-Panel buttons extremely difficult to push to enable.
-Heat probe sensor already replaced.
-Baking element already replaced.
Repaired
Newnan, GeorgiaKenmore9114012190WB27K5055F1F1Awaiting receipt of timer
HUNTSVILLE, AlabamaLGJD527GOP1BGWB27K5055NC-RANGE TEMP WILL NWHEN SETTING RANGE TEMP, A LOUD "DUCK" SOUND COMES FROM THE MODULE AND THE TEMP WILL NOT SET OR HOLD. IT WILL SOMETIMES ACK AS IF IT IS HEATING UP AND WILL SHUTOFF.Repaired
SUMMERVILLE, South CarolinaGeneral ElectricJDS27GOP2BGWB27K5055N/ATIMER COMES ON BUT ELEMENTS IN OVEN DO NOT HEAT UP . AFTER A FEWW SECONDS IT TURNS ITSELF OFF.Repaired
Mascotte, FloridaKenmoreWB27K5055F1Waont warm and beeps.Awaiting receipt of timer
Parsons, TennesseeGeneral ElectricJDC27GoP1BGWB27K5055unknownShows 195* temp at room temp. Will not reach selected tempAwaiting receipt of timer
Pass Christian, MississippiKenmore9114012190WB27K5055NONEwhen I turn it on it only stays on for a few minutes then it turns back off.Repaired
MORGANTOWN, West VirginiaGeneral ElectricJDS27G0P2BGWB27K5055NO CODEBAKE WILL NOT HEAT UP AND ELEMENT IS GOOD.BROIL AND ALL OTHER LIGHTS WORK I THINK. NO POWER TO LOWER ELEMENTRepaired
Naples, FloridaGeneral ElectricJDC27G0P1BGWB27K5055noneOven timer "beeps" in 1-2 minutes indicating that selected bake temperature has been reached when this is not correct. Temperature selector must be set to max in order to achieve about a 400 temp. Broiler element seems to work OKAwaiting receipt of timer
Bristol, ConnecticutGeneral ElectricJDS26G0R2ADWB27K5055None shownClock works. Bake and Broil functions buss when selecting them. Also the lower oven coil heats up when selecting the Broil Function (the upper coil does not heat up). When selecting the bake function and touching the up arrow the digital window shows 350 degrees on top and 100 degrees on the bottom, the lower coil begins to heat, but the digital lights go out after about 10 or 15 seconds and the coil begins to cool.Awaiting receipt of timer
West Bloomfield, MichiganGeneral ElectricJDC27GP2BGwb27k5055no code given.Wont gWont get to temp. at 500 it only gets to 299
We need at least a referb if you have one please
Awaiting receipt of timer